On my 35/3 it is set to 14 degrees. The Kanzai transmission is 2.6 to 1. The newer models can be adjusted under water. The old ones cannot.
I agree that Fred Hutchinson is the best place to start. Joel On Mon, Jul 28, 2014 at 12:24 AM, Josh Muckley via CnC-List < cnc-list@cnc-list.com> wrote: > Some other things to consider. Is the bottom clean? It the 2000 rpm > while tied to the dock? > > Josh > On Jul 28, 2014 12:16 AM, "Bill Hoyne via CnC-List" <cnc-list@cnc-list.com> > wrote: > >> Hi All, >> I have a Max Prop of unknown diameter (forgot to measure when I had the >> boat out of the water). I also have a Volvo Penta 2003 and when I run the >> engine in idle I get 3000+ RPM,s but when I run it in gear I only get >> 1900-2000 RPM’s. I suspect the pitch is a little high. ( A dripless seal, >> new shaft and cutless bering were installed last year and in the process >> the max-prop was taken off and may not have been installed with the >> original specs of which I don’t have from the PO.) My question in does >> anybody out there know what the X,Y values should be for a typical C&C >> MKII? I would like a starting point to compare what is in the prop now and >> where I should head to. The other question is can I do thin in the water or >> do I need to haul the boat? >> Thanks, >> Bill >> >> >> >> *Bill Hoyne* >> Mithrandir >> ’74 C&C35 MkII >> in Victoria,BC >> >> >> >> On Jul 24, 2014, at 5:01 PM, Chuck S via CnC-List <cnc-list@cnc-list.com> >> wrote: >> >> As stated before, I like to follow the manufacturer's recommendation and >> use Lubriplate 130 AA for MaxProp. It is a grease that works well on >> bronze parts. The base is the same for Lewmar winch grease. I opened our >> MaxProp this winter after 7 years on the boat, and found the metal clean, >> bright gold in color, and shiny. No oxidation at all. Thanks, Lubriplate. >> >> >> >> Chuck >> Resolute >> 1990 C&C 34R >> Broad Creek, Magothy River, Md >> >> ------------------------------ >> *From: *"CNC boat owners, cnc-list" <cnc-list@cnc-list.com> >> *To: *"CNC boat owners, cnc-list" <cnc-list@cnc-list.com> >> *Sent: *Thursday, July 24, 2014 10:23:50 AM >> *Subject: *Stus-List Prop Grease >> >> Subject change. >> >> Has anyone tried Krazy Grease, a waterproof grease in cartridges that is >> advertised as being the greatest thing since short skirts? >> >> Might be good on MaxProps etc. >> >> See www.krazygrease.com >> >> Rich Knowles >> INDIGO LF38 >> Halifax, NS. >> >> >> >> _______________________________________________ >> This List is provided by the C&C Photo Album >> >> Email address: >> CnC-List@cnc-list.com >> To change your list preferences, including unsubscribing -- go bottom of >> page at: >> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com >> >> >> _______________________________________________ >> This List is provided by the C&C Photo Album >> >> Email address: >> CnC-List@cnc-list.com >> To change your list preferences, including unsubscribing -- go bottom of >> page at: >> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com >> >> >> >> _______________________________________________ >> This List is provided by the C&C Photo Album >> >> Email address: >> CnC-List@cnc-list.com >> To change your list preferences, including unsubscribing -- go bottom of >> page at: >> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com >> >> >> > _______________________________________________ > This List is provided by the C&C Photo Album > > Email address: > CnC-List@cnc-list.com > To change your list preferences, including unsubscribing -- go bottom of > page at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > > > -- Joel 301 541 8551
_______________________________________________ This List is provided by the C&C Photo Album Email address: CnC-List@cnc-list.com To change your list preferences, including unsubscribing -- go bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com
