I fitted them to my 24 and they worked fine, were a struggle to get on but that meant they never slipped. Cheers Paul
To: cnc-list@cnc-list.com Date: Tue, 8 Sep 2015 17:08:15 -0300 Subject: Re: Stus-List Barient ST 32's From: cnc-list@cnc-list.com CC: rtaill...@eastlink.ca I have them on my 25 and they work great. They came on a pair of Barient 18s that I traded for another pair of winches I had and some splicing jobs.I don’t know what size they are but they almost look a size too small for the winches, maybe that’s why I haven’t had the slippage problems that some people have had. There is no way I could get my normal sheets in the outer groove but my light air ones do fit. I use 5/16” sheets and the key is to get three full wraps on the winch then grind it in to jam the top wrap against the bottom of the Wincher, if I don’t do that the sheet will back off. I like them because you can take in the majority of the sheet before the load comes on then put on the third wrap and finish trimming in the sail with one hand, great for single handed sailing. I still have to deal with the sheet as it comes off the winch but I can crank it in a couple turns before it gets around to the front of the winch, if you have someone to tail this is a non-issue. Rick TaillieuNemesis'75 C&C 25 #371Shearwater Yacht ClubHalifax, NS. From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Marek Dziedzic via CnC-List Sent: September-07-15 19:16 To: C&C List Cc: Marek Dziedzic Subject: Re: Stus-List Barient ST 32's I had them on my C&C 24 and I could not make them to work. I removed them. But ymmv. Marek Sent from my Samsung device over Bell's LTE network. -------- Original message -------- From: David Knecht via CnC-List <cnc-list@cnc-list.com> Date: 2015-09-07 18:07 (GMT-05:00) To: CnC CnC discussion list <cnc-list@cnc-list.com> Cc: David Knecht <davidakne...@gmail.com> Subject: Re: Stus-List Barient ST 32's What about $50 for Winchers (http://www.defender.com/product3.jsp?path=-1%7C118%7C2358547%7C2358555&id=899493)? I am considering trying one for one of my cabin top small secondaries. I have read that they work. Dave Aries1990 C&C 34+New London, CT On Sep 7, 2015, at 5:05 PM, Dennis C. via CnC-List <cnc-list@cnc-list.com> wrote: Pairs of used self tailers on eBay go for $1000-1800 depending on size. (There's a pair of 60 ST's out there now for $1700.) Winchmates are ~$550 each. That's $1100 a pair.Good used non-self tailers sell for $300-800 on eBay depending on size and condition. I upgraded Touche's primary, secondary and cabin top winches from alloy to chrome bronze. Net cost for 2 Barlow 28's, 2 Barlow 26's and 2 stainless Barient 22's (all used non ST's) was around $600. Paid $1100 for the "new" ones and sold two pairs of the old ones on eBay for $500 and tossed a pair of 28's in the dumpster. Just saying....Dennis C. On Mon, Sep 7, 2015 at 3:13 PM, Harry Hallgring via CnC-List <cnc-list@cnc-list.com> wrote:Bill,Yes, that is probably what I will do for my primaries. HarrySent from my iPad On Sep 7, 2015, at 11:07 AM, Bill Coleman via CnC-List <cnc-list@cnc-list.com> wrote:These? http://www.winchmate.com/store.html Bill ColemanC&C 39 _______________________________________________ Email address: CnC-List@cnc-list.com To change your list preferences, including unsubscribing -- go to the bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com _______________________________________________ Email address: CnC-List@cnc-list.com To change your list preferences, including unsubscribing -- go to the bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com No virus found in this message. Checked by AVG - www.avg.com Version: 2015.0.6125 / Virus Database: 4419/10600 - Release Date: 09/08/15 _______________________________________________ Email address: CnC-List@cnc-list.com To change your list preferences, including unsubscribing -- go to the bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com
_______________________________________________ Email address: CnC-List@cnc-list.com To change your list preferences, including unsubscribing -- go to the bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com
