That's too bad! Time for plan B. Gary S/V High Maintenance '90 C&C 37 Plus East Greenwich, RI, USA
~~~~~~~_/)~~~~~~ On Sat, Dec 12, 2015 at 9:17 PM, Ken Heaton via CnC-List < cnc-list@cnc-list.com> wrote: > I'm pretty sure mine does not have a full length keyway and it didn't have > a factory autopilot either. > > Ken H. > > S/V Salazar > C&C 37 XL > > On 12 December 2015 at 21:54, Gary Russell via CnC-List < > cnc-list@cnc-list.com> wrote: > >> Josh, >> I'm wondering if all 37 Pluses have a full length keyway, or only >> boats with the factory autopilot installation. >> >> Gary >> S/V High Maintenance >> '90 C&C 37 Plus >> East Greenwich, RI, USA >> >> ~~~~~~~_/)~~~~~~ >> >> >> On Sat, Dec 12, 2015 at 5:56 PM, Josh Muckley via CnC-List < >> cnc-list@cnc-list.com> wrote: >> >>> Gary, >>> >>> Autopilot was already there. >>> >>> Keyway goes almost the full length of the rudder stock. >>> >>> I think this may have been a factory install since the platform in >>> Brian's boat looks exactly like mine. >>> >>> Josh Muckley >>> S/V Sea Hawk >>> 1989 C&C 37+ >>> Solomons, MD >>> On Dec 12, 2015 5:02 PM, "Gary Russell via CnC-List" < >>> cnc-list@cnc-list.com> wrote: >>> >>>> Josh, >>>> Did you install the autopilot or a PO? If you installed it was >>>> the rudder cut out when you got it and did the shaft have a keyway already >>>> cut in it. >>>> >>>> Gary >>>> S/V High Maintenance >>>> '90 C&C 37 Plus >>>> East Greenwich, RI, USA >>>> >>>> ~~~~~~~_/)~~~~~~ >>>> >>>> >>>> On Fri, Dec 11, 2015 at 6:38 PM, Josh Muckley via CnC-List < >>>> cnc-list@cnc-list.com> wrote: >>>> >>>>> I've removed my rudder arm and it looked nothing like that. It looks >>>>> like you are looking at the back side. The 4 bolts accessible from the >>>>> front are all you need to remove. >>>>> >>>>> https://drive.google.com/folder/d/0B8pEh5lnvP1yZU1hczd0QlNEOWc/edit >>>>> >>>>> https://drive.google.com/folder/d/0B8pEh5lnvP1yVUdWUDNxVGFUcDA/edit >>>>> >>>>> https://drive.google.com/folder/d/0B8pEh5lnvP1yQWIyanRiTzBKRlk/edit >>>>> >>>>> Josh Muckley >>>>> S/V Sea Hawk >>>>> 1989 C&C 37+ >>>>> Solomons, MD >>>>> On Dec 11, 2015 6:23 PM, "Brian Fry via CnC-List" < >>>>> cnc-list@cnc-list.com> wrote: >>>>> >>>>>> Hello, my name is Brian. I recently bought La Neige, a 1993 37/40xl. >>>>>> I am in the Chesapeake. >>>>>> >>>>>> http://i.imgur.com/5faMwZ9.jpg >>>>>> >>>>>> The link is to a picture of my C&C 37/40 auto pilot clamp, where it >>>>>> attaches to the rudder shaft. The threaded rod has no bolt head to >>>>>> unscrew >>>>>> the rod. >>>>>> Has anyone dealt with this issue? I need to drop my rudder, and this >>>>>> is not allowing that to happen. >>>>>> . >>>>>> >>>>>> _______________________________________________ >>>>>> >>>>>> Email address: >>>>>> CnC-List@cnc-list.com >>>>>> To change your list preferences, including unsubscribing -- go to the >>>>>> bottom of page at: >>>>>> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com >>>>>> >>>>>> >>>>>> >>>>> _______________________________________________ >>>>> >>>>> Email address: >>>>> CnC-List@cnc-list.com >>>>> To change your list preferences, including unsubscribing -- go to the >>>>> bottom of page at: >>>>> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com >>>>> >>>>> >>>>> >>>> >>>> _______________________________________________ >>>> >>>> Email address: >>>> CnC-List@cnc-list.com >>>> To change your list preferences, including unsubscribing -- go to the >>>> bottom of page at: >>>> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com >>>> >>>> >>>> >>> _______________________________________________ >>> >>> Email address: >>> CnC-List@cnc-list.com >>> To change your list preferences, including unsubscribing -- go to the >>> bottom of page at: >>> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com >>> >>> >>> >> >> _______________________________________________ >> >> Email address: >> CnC-List@cnc-list.com >> To change your list preferences, including unsubscribing -- go to the >> bottom of page at: >> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com >> >> >> > > _______________________________________________ > > Email address: > CnC-List@cnc-list.com > To change your list preferences, including unsubscribing -- go to the > bottom of page at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > > >
_______________________________________________ Email address: CnC-List@cnc-list.com To change your list preferences, including unsubscribing -- go to the bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com