No, that’s adhesive, not sealant. I think heating it and re-clamping would probably seal it, if it is the hose. If you can shut off the thru hull, and it sounds like you can, you can remove the hose, and then remove the barbed adapter and see what is wrong. Either re-seat it, or get a new one.
Bill Coleman Entrada, Erie, PA From: Peter McMinn [mailto:petemcm...@gmail.com] Sent: Wednesday, October 21, 2020 7:06 PM To: Stus-List Subject: Stus-List Re: leaky head intake I have 3m 5200 but don’t think that’s the stuff. Or is it? On Wed, Oct 21, 2020 at 3:57 PM Andrew Burton <a.burton.sai...@gmail.com> wrote: I would never use actual silicone sealant. Once you do, nothing else will stick. Andy Andrew Burton 26 <https://www.google.com/maps/search/26+Beacon+Hill+Newport,+RI+USA++02840?entry=gmail&source=g> Beacon Hill Newport, <https://www.google.com/maps/search/26+Beacon+Hill+Newport,+RI+USA++02840?entry=gmail&source=g> RI USA <https://www.google.com/maps/search/26+Beacon+Hill+Newport,+RI+USA++02840?entry=gmail&source=g> 02840 <https://www.google.com/maps/search/26+Beacon+Hill+Newport,+RI+USA++02840?entry=gmail&source=g> http://sites.google.com/site/andrewburtonyachtservices/ +401 965-5260 On Oct 21, 2020, at 18:04, Peter McMinn <petemcm...@gmail.com> wrote: Ha! Yes, I'm talking about the intake for the head (toilet). Great suggestions here. In the interest of not turning a tiny leak into a gushing one (or an inoperative toilet), I think I'll try the least disruptive first: 1. rescue tape 2. removing/trimming the hose and applying silicone & replacing or 3. removing/trimming/replacing the hose and lightly heating with even clamping Lots to mull here-- thanks for the ideas. Richard, thanks for the warm welcome and the reference to Dave Godwin's blog. I'll be in touch with him! Peter McMinn _/) On Wed, Oct 21, 2020 at 1:41 PM Brian Davis <brianwdavis...@gmail.com> wrote: Ah ha!! My motor head went to engine. Hahaha On Wed, Oct 21, 2020, 3:26 PM Bill Coleman <colt...@gmail.com> wrote: I am pretty sure Peter is talking about his head, as in toilet, rather than Head, on his engine, if that is what you are thinking? Bill Coleman Entrada, Erie, PA From: Brian Davis [mailto:brianwdavis...@gmail.com] Sent: Wednesday, October 21, 2020 12:20 PM To: Stus-List Subject: Stus-List Re: leaky head intake Hi Peter, I just recently rebuilt my Yanmar and replaced all hoses that you mentioned. I'm a little confused when you say Plastic seacock... However, if you remove that end of the hose and can cut 1 inch off and then use a silicone type of sealant that may hold you over. Also, at some point you may want to remove the exhaust manifold and have it sand blasted and reinstall with a new gasket too. I had a lot of carbon build up inside mine which can lead to pressure that may also cause a leak. A lot radiator shop can blast it for cheap. Just added 2 cents.. Brian 1980 Landfall 38SL sv Nina On Wed, Oct 21, 2020, 10:53 AM Peter McMinn <petemcm...@gmail.com> wrote: Hello C&Crs. My wife & I are the excited new owners of Sirius, '85 C&C 37 located for now in Poulsbo, WA. We’ll be adventuring north in the coming years but sailing Puget Sound and San Juans for the time being. The boat has received incredible care and maintenance by the PO but comes equipped with a leaky head intake where the hose meets the barbed nipple on the plastic seacock. Guessing the nipple is cracked or scored, preventing the clamp from sealing properly. It drips about 1/5 secs and needs attention, but I don't want to break it with too much tightening. Thinking of removing the hose and coating nipple with a good sealant then retightening until I can replace the seacock next haul. A durable bandaid or am I asking for disaster? I'll be signing up for the meet 'n greet next week, so maybe I'll see you there. C&C 37 Hull 128 Peter McMinn _/) October is the time to show your appreciation with a small contribution to this list to help offset the costs. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray Thanks - Stu October is the time to show your appreciation with a small contribution to this list to help offset the costs. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray Thanks - Stu October is the time to show your appreciation with a small contribution to this list to help offset the costs. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray Thanks - Stu October is the time to show your appreciation with a small contribution to this list to help offset the costs. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray Thanks - Stu October is the time to show your appreciation with a small contribution to this list to help offset the costs. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray Thanks - Stu -- Peter McMinn _/)
October is the time to show your appreciation with a small contribution to this list to help offset the costs. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray Thanks - Stu