You shall troubleshoot in the following steps:
1). Bring up the physical ethernet connection between your PC and the
USRP. Upon successful you will see the LED turns on at the USRP GE port.
2). Set your PC IP address to the same subnet but don't crash with the
USRP's ip address.
If this step is successful then you will be able to ping the USRP.
3). Issue command "uhd_find_devices" and you will see the USRP being
discovered.
Then you could proceed with "uhd_usrp_probe" to see more details.
On Mon, Oct 21, 2013 at 1:00 PM, Sandhya G <sandhya4...@gmail.com> wrote:
> ya its a new one and sir y i'am i getting unknown key format even though i
> give addr=192.168.10.2 and the problem i'm facing is its showing me an
> error has cannot find as a single device.I have no clue the reason for that
>
> Thanks and regards
> Sandhya
>
>
> On Mon, Oct 21, 2013 at 10:24 AM, Activecat <active...@gmail.com> wrote:
>
>> If that is a new USRP from factory then you don't need to update the
>> firmware.
>>
>>
>>
>> On Mon, Oct 21, 2013 at 12:51 PM, Sandhya G <sandhya4...@gmail.com>wrote:
>>
>>> Thanks for the reply.
>>> Well is that only problem so that i'm unable to communicate and should i
>>> need to update the firmware?
>>>
>>>
>>> Thanks and regards
>>> Sandhya.G
>>>
>>>
>>> On Mon, Oct 21, 2013 at 10:19 AM, Activecat <active...@gmail.com> wrote:
>>>
>>>> Your pc must have 1000Mbps port. The 10/100Mbps won't work.
>>>> An alternative is to connect a 10/100/1000 LAN switch between your pc
>>>> and the USRP.
>>>>
>>>> Rgds,
>>>> activecat.
>>>>
>>>>
>>>> On Mon, Oct 21, 2013 at 12:37 PM, Sandhya G <sandhya4...@gmail.com>wrote:
>>>>
>>>>> HI all,
>>>>>
>>>>>
>>>>> I have followed as per the instructions given in the webpage for set
>>>>> up of the Usrp N200/N210 but still i am unable to communicate between the
>>>>> hardware and host pc
>>>>>
>>>>>
>>>>>
>>>>> 1.I have set the static ip of the host pc to
>>>>> 192.168.10.1(ifconfig eth0 192.168.10.1).
>>>>>
>>>>> 2.Whenever i give the device address=addr=192.168.10.1 and run the grc
>>>>> i am getting the error has “*unknown key format*”
>>>>>
>>>>> 3.Whenever i ping 192.168.10.2 or use the command uhb_find_device i
>>>>> am getting warning as “*NO DEVICE FOUND* “
>>>>>
>>>>> 4. Is that a must i have to upload the fpga and firmware images when
>>>>> using the device for the first time.
>>>>>
>>>>> 5.Sometimes i am getting an error like”* unable to find as single
>>>>> device”.*
>>>>>
>>>>> *6.*The* *host pc is supporting only 10/100MBPS .Is that the only
>>>>> problem so that i am unable to communicate with the hardware.
>>>>>
>>>>>
>>>>>
>>>>> Can anybody help me on this issue.Awaiting for your valuable reply
>>>>>
>>>>>
>>>>> Thanks in advance
>>>>>
>>>>> Sandhya.G
>>>>>
>>>>> _______________________________________________
>>>>> Discuss-gnuradio mailing list
>>>>> Discuss-gnuradio@gnu.org
>>>>> https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
>>>>>
>>>>>
>>>>
>>>
>>
>
_______________________________________________
Discuss-gnuradio mailing list
Discuss-gnuradio@gnu.org
https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
