OS is linux. my pc is 2010 model,has
- 3rd Generation Intel® Core™ i5-3317U
- 64-bit.
And when i give the command sudo ethtool eth1 i'am getting the speed has
10Mb/s
Settings for eth1:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Speed: 10Mb/s
Duplex: Half
Port: MII
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: pumbg
Wake-on: g
Current message level: 0x00000033 (51)
drv probe ifdown ifup
Link detected: no
And ya GE port led is not ON
Thanks
Sandhya
On Mon, Oct 21, 2013 at 11:04 AM, Activecat <active...@gmail.com> wrote:
> What operating system are you running, is it Linux or Microsoft Windows?
>
>
> On Mon, Oct 21, 2013 at 1:25 PM, Sandhya G <sandhya4...@gmail.com> wrote:
>
>> i'm seeing only LED's D and F are on, because host pc is not at all
>> detecting the hardware and i'm unable to run any operation.In my first i
>> mentioned the errors what i'am getting when i run the flowgraph.
>> Even i'am clueless how my device is only showing up 10/100Mbps when i
>> connect the hardware and even i tried with other pc but i'm facing the same
>> problem.
>>
>>
>> Thanks and regards
>> Sandhya
>>
>>
>> On Mon, Oct 21, 2013 at 10:42 AM, Activecat <active...@gmail.com> wrote:
>>
>>> What operating are you running? How do you get the "10/100Mbps" ? Do
>>> you see the LED turns on at the USRP GE port?
>>>
>>>
>>> On Mon, Oct 21, 2013 at 1:09 PM, Sandhya G <sandhya4...@gmail.com>wrote:
>>>
>>>> Sir my pc is capable of supporting 1000Mbps but when i connect the
>>>> hardware and check the speed of the port it will be showing 10/100Mbps.
>>>> What might the issue?and can i boost the pc speed
>>>>
>>>> Thanks and regards
>>>> Sandhya
>>>>
>>>>
>>>> On Mon, Oct 21, 2013 at 10:30 AM, Sandhya G <sandhya4...@gmail.com>wrote:
>>>>
>>>>> ya its a new one and sir y i'am i getting unknown key format even
>>>>> though i give addr=192.168.10.2 and the problem i'm facing is its showing
>>>>> me an error has cannot find as a single device.I have no clue the reason
>>>>> for that
>>>>>
>>>>> Thanks and regards
>>>>> Sandhya
>>>>>
>>>>>
>>>>> On Mon, Oct 21, 2013 at 10:24 AM, Activecat <active...@gmail.com>wrote:
>>>>>
>>>>>> If that is a new USRP from factory then you don't need to update the
>>>>>> firmware.
>>>>>>
>>>>>>
>>>>>>
>>>>>> On Mon, Oct 21, 2013 at 12:51 PM, Sandhya G <sandhya4...@gmail.com>wrote:
>>>>>>
>>>>>>> Thanks for the reply.
>>>>>>> Well is that only problem so that i'm unable to communicate and
>>>>>>> should i need to update the firmware?
>>>>>>>
>>>>>>>
>>>>>>> Thanks and regards
>>>>>>> Sandhya.G
>>>>>>>
>>>>>>>
>>>>>>> On Mon, Oct 21, 2013 at 10:19 AM, Activecat <active...@gmail.com>wrote:
>>>>>>>
>>>>>>>> Your pc must have 1000Mbps port. The 10/100Mbps won't work.
>>>>>>>> An alternative is to connect a 10/100/1000 LAN switch between your
>>>>>>>> pc and the USRP.
>>>>>>>>
>>>>>>>> Rgds,
>>>>>>>> activecat.
>>>>>>>>
>>>>>>>>
>>>>>>>> On Mon, Oct 21, 2013 at 12:37 PM, Sandhya G
>>>>>>>> <sandhya4...@gmail.com>wrote:
>>>>>>>>
>>>>>>>>> HI all,
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> I have followed as per the instructions given in the webpage for
>>>>>>>>> set up of the Usrp N200/N210 but still i am unable to communicate
>>>>>>>>> between
>>>>>>>>> the hardware and host pc
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> 1.I have set the static ip of the host pc to
>>>>>>>>> 192.168.10.1(ifconfig eth0 192.168.10.1).
>>>>>>>>>
>>>>>>>>> 2.Whenever i give the device address=addr=192.168.10.1 and run the
>>>>>>>>> grc i am getting the error has “*unknown key format*”
>>>>>>>>>
>>>>>>>>> 3.Whenever i ping 192.168.10.2 or use the command uhb_find_device
>>>>>>>>> i am getting warning as “*NO DEVICE FOUND* “
>>>>>>>>>
>>>>>>>>> 4. Is that a must i have to upload the fpga and firmware images
>>>>>>>>> when using the device for the first time.
>>>>>>>>>
>>>>>>>>> 5.Sometimes i am getting an error like”* unable to find as single
>>>>>>>>> device”.*
>>>>>>>>>
>>>>>>>>> *6.*The* *host pc is supporting only 10/100MBPS .Is that the only
>>>>>>>>> problem so that i am unable to communicate with the hardware.
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> Can anybody help me on this issue.Awaiting for your valuable reply
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> Thanks in advance
>>>>>>>>>
>>>>>>>>> Sandhya.G
>>>>>>>>>
>>>>>>>>> _______________________________________________
>>>>>>>>> Discuss-gnuradio mailing list
>>>>>>>>> Discuss-gnuradio@gnu.org
>>>>>>>>> https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
>>>>>>>>>
>>>>>>>>>
>>>>>>>>
>>>>>>>
>>>>>>
>>>>>
>>>>
>>>
>>
>
_______________________________________________
Discuss-gnuradio mailing list
Discuss-gnuradio@gnu.org
https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
