What operating system are you running, is it Linux or Microsoft Windows?
On Mon, Oct 21, 2013 at 1:25 PM, Sandhya G <sandhya4...@gmail.com> wrote: > i'm seeing only LED's D and F are on, because host pc is not at all > detecting the hardware and i'm unable to run any operation.In my first i > mentioned the errors what i'am getting when i run the flowgraph. > Even i'am clueless how my device is only showing up 10/100Mbps when i > connect the hardware and even i tried with other pc but i'm facing the same > problem. > > > Thanks and regards > Sandhya > > > On Mon, Oct 21, 2013 at 10:42 AM, Activecat <active...@gmail.com> wrote: > >> What operating are you running? How do you get the "10/100Mbps" ? Do you >> see the LED turns on at the USRP GE port? >> >> >> On Mon, Oct 21, 2013 at 1:09 PM, Sandhya G <sandhya4...@gmail.com> wrote: >> >>> Sir my pc is capable of supporting 1000Mbps but when i connect the >>> hardware and check the speed of the port it will be showing 10/100Mbps. >>> What might the issue?and can i boost the pc speed >>> >>> Thanks and regards >>> Sandhya >>> >>> >>> On Mon, Oct 21, 2013 at 10:30 AM, Sandhya G <sandhya4...@gmail.com>wrote: >>> >>>> ya its a new one and sir y i'am i getting unknown key format even >>>> though i give addr=192.168.10.2 and the problem i'm facing is its showing >>>> me an error has cannot find as a single device.I have no clue the reason >>>> for that >>>> >>>> Thanks and regards >>>> Sandhya >>>> >>>> >>>> On Mon, Oct 21, 2013 at 10:24 AM, Activecat <active...@gmail.com>wrote: >>>> >>>>> If that is a new USRP from factory then you don't need to update the >>>>> firmware. >>>>> >>>>> >>>>> >>>>> On Mon, Oct 21, 2013 at 12:51 PM, Sandhya G <sandhya4...@gmail.com>wrote: >>>>> >>>>>> Thanks for the reply. >>>>>> Well is that only problem so that i'm unable to communicate and >>>>>> should i need to update the firmware? >>>>>> >>>>>> >>>>>> Thanks and regards >>>>>> Sandhya.G >>>>>> >>>>>> >>>>>> On Mon, Oct 21, 2013 at 10:19 AM, Activecat <active...@gmail.com>wrote: >>>>>> >>>>>>> Your pc must have 1000Mbps port. The 10/100Mbps won't work. >>>>>>> An alternative is to connect a 10/100/1000 LAN switch between your >>>>>>> pc and the USRP. >>>>>>> >>>>>>> Rgds, >>>>>>> activecat. >>>>>>> >>>>>>> >>>>>>> On Mon, Oct 21, 2013 at 12:37 PM, Sandhya G >>>>>>> <sandhya4...@gmail.com>wrote: >>>>>>> >>>>>>>> HI all, >>>>>>>> >>>>>>>> >>>>>>>> I have followed as per the instructions given in the webpage for >>>>>>>> set up of the Usrp N200/N210 but still i am unable to communicate >>>>>>>> between >>>>>>>> the hardware and host pc >>>>>>>> >>>>>>>> >>>>>>>> >>>>>>>> 1.I have set the static ip of the host pc to >>>>>>>> 192.168.10.1(ifconfig eth0 192.168.10.1). >>>>>>>> >>>>>>>> 2.Whenever i give the device address=addr=192.168.10.1 and run the >>>>>>>> grc i am getting the error has “*unknown key format*” >>>>>>>> >>>>>>>> 3.Whenever i ping 192.168.10.2 or use the command uhb_find_device >>>>>>>> i am getting warning as “*NO DEVICE FOUND* “ >>>>>>>> >>>>>>>> 4. Is that a must i have to upload the fpga and firmware images >>>>>>>> when using the device for the first time. >>>>>>>> >>>>>>>> 5.Sometimes i am getting an error like”* unable to find as single >>>>>>>> device”.* >>>>>>>> >>>>>>>> *6.*The* *host pc is supporting only 10/100MBPS .Is that the only >>>>>>>> problem so that i am unable to communicate with the hardware. >>>>>>>> >>>>>>>> >>>>>>>> >>>>>>>> Can anybody help me on this issue.Awaiting for your valuable reply >>>>>>>> >>>>>>>> >>>>>>>> Thanks in advance >>>>>>>> >>>>>>>> Sandhya.G >>>>>>>> >>>>>>>> _______________________________________________ >>>>>>>> Discuss-gnuradio mailing list >>>>>>>> Discuss-gnuradio@gnu.org >>>>>>>> https://lists.gnu.org/mailman/listinfo/discuss-gnuradio >>>>>>>> >>>>>>>> >>>>>>> >>>>>> >>>>> >>>> >>> >> >
_______________________________________________ Discuss-gnuradio mailing list Discuss-gnuradio@gnu.org https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
