Congradulation and you are most welcome. activecat.
On Mon, Oct 21, 2013 at 7:10 PM, Sandhya G <sandhya4...@gmail.com> wrote: > Yes sir .your right i thought my pc is ethernet capable.I brushed the spec > of pc hardware it just supports maximum 100mbps .so i'm installing gnuradio > on pandaboard which supports gigabyte. > > > Thanks and regards > Sandhya > > > On Mon, Oct 21, 2013 at 11:58 AM, Activecat <active...@gmail.com> wrote: > >> Chances are your pc hardware is actually not GE capable. >> >> >> On Mon, Oct 21, 2013 at 2:23 PM, Sandhya G <sandhya4...@gmail.com> wrote: >> >>> ok sir then i'l try to debug the problem in my os now >>> >>> Thanks >>> Sandhya >>> >>> >>> On Mon, Oct 21, 2013 at 11:49 AM, Activecat <active...@gmail.com> wrote: >>> >>>> As I mentioned in previous email (below), the first thing you need to >>>> do now is to bring up the physical layer of the Ethernet connection. >>>> If the GE port LED is not ON, no point to proceed without this being >>>> solved first. >>>> >>>> If you insist that your hardware support 1000Mbps GE, then make the >>>> Linux recognise this first before troubleshooting at the gnuradio level. >>>> >>>> Now you should troubleshoot your Linux, not gnuradio, if you confirmed >>>> that your hardware is really GE capable. >>>> >>>> >>>> ---------- Forwarded message ---------- >>>> From: Activecat <active...@gmail.com> >>>> Date: Mon, Oct 21, 2013 at 1:09 PM >>>> Subject: Re: [Discuss-gnuradio] setup of usrp N100/N200 >>>> To: Sandhya G <sandhya4...@gmail.com> >>>> Cc: Discuss-gnuradio@gnu.org >>>> >>>> You shall troubleshoot in the following steps: >>>> >>>> 1). Bring up the physical ethernet connection between your PC and the >>>> USRP. Upon successful you will see the LED turns on at the USRP GE port. >>>> >>>> 2). Set your PC IP address to the same subnet but don't crash with the >>>> USRP's ip address. >>>> If this step is successful then you will be able to ping the USRP. >>>> >>>> 3). Issue command "uhd_find_devices" and you will see the USRP being >>>> discovered. >>>> >>>> Then you could proceed with "uhd_usrp_probe" to see more details. >>>> >>>> >>>> On Mon, Oct 21, 2013 at 2:02 PM, Sandhya G <sandhya4...@gmail.com>wrote: >>>> >>>>> OS is linux. my pc is 2010 model,has >>>>> >>>>> - 3rd Generation Intel® Core™ i5-3317U >>>>> - 64-bit. >>>>> >>>>> And when i give the command sudo ethtool eth1 i'am getting the speed >>>>> has 10Mb/s >>>>> >>>>> Settings for eth1: >>>>> Supported ports: [ TP MII ] >>>>> Supported link modes: 10baseT/Half 10baseT/Full >>>>> 100baseT/Half 100baseT/Full >>>>> Supported pause frame use: No >>>>> Supports auto-negotiation: Yes >>>>> Advertised link modes: 10baseT/Half 10baseT/Full >>>>> 100baseT/Half 100baseT/Full >>>>> Advertised pause frame use: Symmetric Receive-only >>>>> Advertised auto-negotiation: Yes >>>>> Speed: 10Mb/s >>>>> Duplex: Half >>>>> Port: MII >>>>> PHYAD: 0 >>>>> Transceiver: internal >>>>> Auto-negotiation: on >>>>> Supports Wake-on: pumbg >>>>> Wake-on: g >>>>> Current message level: 0x00000033 (51) >>>>> drv probe ifdown ifup >>>>> Link detected: no >>>>> >>>>> And ya GE port led is not ON >>>>> >>>>> Thanks >>>>> >>>>> Sandhya >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> On Mon, Oct 21, 2013 at 11:04 AM, Activecat <active...@gmail.com>wrote: >>>>> >>>>>> What operating system are you running, is it Linux or Microsoft >>>>>> Windows? >>>>>> >>>>>> >>>>>> On Mon, Oct 21, 2013 at 1:25 PM, Sandhya G <sandhya4...@gmail.com>wrote: >>>>>> >>>>>>> i'm seeing only LED's D and F are on, because host pc is not at all >>>>>>> detecting the hardware and i'm unable to run any operation.In my first i >>>>>>> mentioned the errors what i'am getting when i run the flowgraph. >>>>>>> Even i'am clueless how my device is only showing up 10/100Mbps when >>>>>>> i connect the hardware and even i tried with other pc but i'm facing the >>>>>>> same problem. >>>>>>> >>>>>>> >>>>>>> Thanks and regards >>>>>>> Sandhya >>>>>>> >>>>>>> >>>>>>> On Mon, Oct 21, 2013 at 10:42 AM, Activecat <active...@gmail.com>wrote: >>>>>>> >>>>>>>> What operating are you running? How do you get the "10/100Mbps" ? >>>>>>>> Do you see the LED turns on at the USRP GE port? >>>>>>>> >>>>>>>> >>>>>>>> On Mon, Oct 21, 2013 at 1:09 PM, Sandhya G >>>>>>>> <sandhya4...@gmail.com>wrote: >>>>>>>> >>>>>>>>> Sir my pc is capable of supporting 1000Mbps but when i connect the >>>>>>>>> hardware and check the speed of the port it will be showing >>>>>>>>> 10/100Mbps. >>>>>>>>> What might the issue?and can i boost the pc speed >>>>>>>>> >>>>>>>>> Thanks and regards >>>>>>>>> Sandhya >>>>>>>>> >>>>>>>>> >>>>>>>>> On Mon, Oct 21, 2013 at 10:30 AM, Sandhya G <sandhya4...@gmail.com >>>>>>>>> > wrote: >>>>>>>>> >>>>>>>>>> ya its a new one and sir y i'am i getting unknown key format even >>>>>>>>>> though i give addr=192.168.10.2 and the problem i'm facing is its >>>>>>>>>> showing >>>>>>>>>> me an error has cannot find as a single device.I have no clue the >>>>>>>>>> reason >>>>>>>>>> for that >>>>>>>>>> >>>>>>>>>> Thanks and regards >>>>>>>>>> Sandhya >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> On Mon, Oct 21, 2013 at 10:24 AM, Activecat >>>>>>>>>> <active...@gmail.com>wrote: >>>>>>>>>> >>>>>>>>>>> If that is a new USRP from factory then you don't need to update >>>>>>>>>>> the firmware. >>>>>>>>>>> >>>>>>>>>>> >>>>>>>>>>> >>>>>>>>>>> On Mon, Oct 21, 2013 at 12:51 PM, Sandhya G < >>>>>>>>>>> sandhya4...@gmail.com> wrote: >>>>>>>>>>> >>>>>>>>>>>> Thanks for the reply. >>>>>>>>>>>> Well is that only problem so that i'm unable to communicate and >>>>>>>>>>>> should i need to update the firmware? >>>>>>>>>>>> >>>>>>>>>>>> >>>>>>>>>>>> Thanks and regards >>>>>>>>>>>> Sandhya.G >>>>>>>>>>>> >>>>>>>>>>>> >>>>>>>>>>>> On Mon, Oct 21, 2013 at 10:19 AM, Activecat < >>>>>>>>>>>> active...@gmail.com> wrote: >>>>>>>>>>>> >>>>>>>>>>>>> Your pc must have 1000Mbps port. The 10/100Mbps won't work. >>>>>>>>>>>>> An alternative is to connect a 10/100/1000 LAN switch between >>>>>>>>>>>>> your pc and the USRP. >>>>>>>>>>>>> >>>>>>>>>>>>> Rgds, >>>>>>>>>>>>> activecat. >>>>>>>>>>>>> >>>>>>>>>>>>> >>>>>>>>>>>>> On Mon, Oct 21, 2013 at 12:37 PM, Sandhya G < >>>>>>>>>>>>> sandhya4...@gmail.com> wrote: >>>>>>>>>>>>> >>>>>>>>>>>>>> HI all, >>>>>>>>>>>>>> >>>>>>>>>>>>>> >>>>>>>>>>>>>> I have followed as per the instructions given in the webpage >>>>>>>>>>>>>> for set up of the Usrp N200/N210 but still i am unable to >>>>>>>>>>>>>> communicate >>>>>>>>>>>>>> between the hardware and host pc >>>>>>>>>>>>>> >>>>>>>>>>>>>> >>>>>>>>>>>>>> >>>>>>>>>>>>>> 1.I have set the static ip of the host pc to >>>>>>>>>>>>>> 192.168.10.1(ifconfig eth0 192.168.10.1). >>>>>>>>>>>>>> >>>>>>>>>>>>>> 2.Whenever i give the device address=addr=192.168.10.1 and >>>>>>>>>>>>>> run the grc i am getting the error has “*unknown key format* >>>>>>>>>>>>>> ” >>>>>>>>>>>>>> >>>>>>>>>>>>>> 3.Whenever i ping 192.168.10.2 or use the command >>>>>>>>>>>>>> uhb_find_device i am getting warning as “*NO DEVICE FOUND*“ >>>>>>>>>>>>>> >>>>>>>>>>>>>> 4. Is that a must i have to upload the fpga and firmware >>>>>>>>>>>>>> images when using the device for the first time. >>>>>>>>>>>>>> >>>>>>>>>>>>>> 5.Sometimes i am getting an error like”* unable to find as >>>>>>>>>>>>>> single device”.* >>>>>>>>>>>>>> >>>>>>>>>>>>>> *6.*The* *host pc is supporting only 10/100MBPS .Is that the >>>>>>>>>>>>>> only problem so that i am unable to communicate with the >>>>>>>>>>>>>> hardware. >>>>>>>>>>>>>> >>>>>>>>>>>>>> >>>>>>>>>>>>>> >>>>>>>>>>>>>> Can anybody help me on this issue.Awaiting for your valuable >>>>>>>>>>>>>> reply >>>>>>>>>>>>>> >>>>>>>>>>>>>> >>>>>>>>>>>>>> Thanks in advance >>>>>>>>>>>>>> >>>>>>>>>>>>>> Sandhya.G >>>>>>>>>>>>>> >>>>>>>>>>>>>> _______________________________________________ >>>>>>>>>>>>>> Discuss-gnuradio mailing list >>>>>>>>>>>>>> Discuss-gnuradio@gnu.org >>>>>>>>>>>>>> https://lists.gnu.org/mailman/listinfo/discuss-gnuradio >>>>>>>>>>>>>> >>>>>>>>>>>>>> >>>>>>>>>>>>> >>>>>>>>>>>> >>>>>>>>>>> >>>>>>>>>> >>>>>>>>> >>>>>>>> >>>>>>> >>>>>> >>>>> >>>> >>> >> >
_______________________________________________ Discuss-gnuradio mailing list Discuss-gnuradio@gnu.org https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
