As a part of the referenced thread, that's not what it says at all. --- On Wed, 6/26/13, amsct...@comcast.net <amsct...@comcast.net> wrote:
> From: amsct...@comcast.net <amsct...@comcast.net> > Subject: Re: [Elecraft] K3 & SDR/IQ > To: elecraft@mailman.qth.net > Date: Wednesday, June 26, 2013, 12:21 PM > SpectraView's HF tracking mode > doesn't allow for an IF tuning offset on frequencies higher > than the design limit of the SDR-IQ itself. I know the IF > frequency is well below that, but the software was never > supported "tracking panadapter" operation on 6M to the best > of my knowledge. You can still see the IF spectrum, but you > won't have a operator-transparent tracking ability. > > See the Yahoo SDR-IQ group thread on the topic here: > > http://groups.yahoo.com/group/SDR-IQ/message/6543 > > > Mike Alexander - N8MSA > > amsct...@comcast.net > > > ----- Original Message ----- > From: "Joe Subich, W4TV" <li...@subich.com> > > To: elecraft@mailman.qth.net > > Sent: Wednesday, June 26, 2013 2:04:31 PM > Subject: Re: [Elecraft] K3 & SDR/IQ > > > On 6/26/2013 1:43 PM, Wes Stewart wrote: > > LP-Bridge will handle the serial port issue. > > Maybe - if none of your software uses one of the commands > that > LP-Bridge blocks or modifies. The N1MM Logger support team > will not > even accept bug reports if LP-Bridge is involved - any bug > must be > duplicated and documented with LP-Bridge removed due to the > known > issues. > > 73, > > ... Joe, W4TV > > > On 6/26/2013 1:43 PM, Wes Stewart wrote: > > LP-Bridge will handle the serial port issue. I run the > K3, Spectravue, DXBase and N1MM with one USB to Serial > adapter and ports to spare. > > > > > > --- On Tue, 6/25/13, Joe Subich, W4TV <li...@subich.com> > wrote: > > > >> From: Joe Subich, W4TV <li...@subich.com> > > >> Subject: Re: [Elecraft] K3 & SDR/IQ > >> To: elecraft@mailman.qth.net > > >> Date: Tuesday, June 25, 2013, 8:09 PM > >> > >> > So how do yu set it up to watch lower end of > 6m on the > >> K3, without > >> > using a transverter? > >> > >> Connect SDR-IQ to the IF Out jack (not the RX Ant) > and tune > >> SpectraVue > >> to 8.125 MHz manually *or* in SV's "ExtRadio Setup" > Select > >> the K3 and > >> uncheck "HF Tracking Mode." > >> > >> Note: If you want to use the frequency tracking > tied to the > >> IF, you > >> will need some kind of serial splitter to share the > K3 > >> serial port. > >> For more information see the SpectraVue Help file > section > >> 4.2, page > >> 59 and page 58 "IF Tracking". > >> > >> 73, > >> > >> ... Joe, W4TV > >> > >> > >> On 6/25/2013 9:55 PM, KD7YZ Bob wrote: > >>> Howdy K3' people: > >>> > >>> I have an SDR/IQ. I also have three Elecraft > >> transverters. When I > >>> connect a BNC to the BNC-RX "T" chain, and I > tune > >> Spectravue to 28.07 > >>> and the 6m xv50 transverter is "on", I am > looking at > >> the area around > >>> 50.070 .. I can look for beacons and Sporadic-E > > >> openings. > >>> > >>> Nothing new. > >>> > >>> However, the other day, I suspected the xv50 > >> transverter to on the > >>> Fritz. So I switched to the internal 6m Rx/Tx > section. > >> Made some > >>> contacts. > >>> > >>> So now I want to once again look for 6m Beacons > down > >> below 50.080 . > >>> My only option seems to be the IF BNC output. > >>> > >>> I connected there and tried to set Spectravue > for > >> 8.215; 10.0; 28.0 and > >>> still see nothing from 6m. I even tried to set > it at > >> 50.10, to no avail. > >>> > >>> So how do yu set it up to watch lower end of 6m > on the > >> K3, without > >>> using a transverter? > >>> > >>> thanks > >>> > >>> > >> > ______________________________________________________________ > > >> Elecraft mailing list > >> Home: http://mailman.qth.net/mailman/listinfo/elecraft > >> Help: http://mailman.qth.net/mmfaq.htm > >> Post: mailto:Elecraft@mailman.qth.net > > >> > >> This list hosted by: http://www.qsl.net > >> Please help support this email list: http://www.qsl.net/donate.html > >> > > > ______________________________________________________________ > > > Elecraft mailing list > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:Elecraft@mailman.qth.net > > > > > This list hosted by: http://www.qsl.net > > Please help support this email list: http://www.qsl.net/donate.html > > > ______________________________________________________________ > > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html