Honestly, I don't believe this is an issue with LPBridge but rather Eltima
drivers. I can run the Eltima serial port monitor and even without traffic
it will always crash after a number of hours.
Always.
There is not much that can be done other than rebooting after some time or
closing it all when you are not using it.
73 Tom
-----Original Message-----
From: George Kidder
Sent: Tuesday, December 6, 2016 1:37 PM
To: 'Elecraft Reflector'
Subject: [Elecraft] Fwd: Re: LP Bridge crashes with K3
Larry and all,
I have now tried adjusting the buffer settings. Originally, they were
set full "right" (High, 14 for receive, High 16 for transmit) I moved
the sliders to about 3/4 of full scale - still got a LPB crash in about
7 hours, while running NaP3 and FLDigi through LPB. I next tried the
"correct connection problems" setting, full left (1) on each. This time
it ran more than 3 but less than 20 hours (overnight run) and while LPB
did not crash, NaP3 did, which requires complete computer reboot. So it
is not clear that the buffer settings are doing anything except to slow
down the reaction of FLDigi to frequency changes - takes about 5 seconds
now.
So again I am at the end of my short rope! Maybe I should shut down the
system EVERY night. That seems to cure it.
George
-------- Forwarded Message --------
Subject: Re: [Elecraft] LP Bridge crashes with K3
Date: Sun, 04 Dec 2016 18:43:53 -0500
From: George Kidder <gkid...@ilstu.edu>
Reply-To: gkid...@ilstu.edu
To: elecraft@mailman.qth.net
No I have not, Larry. What settings do you recommend for starters?
George
On 12/4/2016 11:02 AM, Larry Phipps wrote:
Have you tried adjusting the buffer settings in Device Mgr for your
serial port?
Larry N8LP
Date: Sat, 3 Dec 2016 09:33:33 -0500
From: George Kidder<gkid...@ilstu.edu>
To: 'Elecraft Reflector'<elecraft@mailman.qth.net>
Subject: [Elecraft] LP Bridge crashes with K3
Message-ID:<a6a9a38b-ed36-ec28-ae6f-e60d63ad2...@ilstu.edu>
Content-Type: text/plain; charset=utf-8; format=flowed
OK, gang! I've tried everything I can think of, and am now looking for
some additional thoughts.
Equipment: K3 (unmodified) with firmware 5.53, computer (2.99 GHz dual
core, 4 GB memory) running Win 7, LP-Bridge (LPB) set for 200 mS delay.
The computer is not connected to the internet, and all programs are
brought in from another computer using a flash drive.
Problem: At random but long intervals (hours) LP-Bridge crashes,
displaying error 13 (type mismatch). Clearing this window causes
program to close. This behavior is seen with no external programs
connected to LPB, and with LPB set to any polling rate from 200 mS
(default) to as much as 1000 mS. It is seen when LPB2 is used and the
baud rate is reduced to 4800. When the crash occurs, the error seems to
be in a response from the K3 - for instance, the "Rig Received Text"
window shows "IS 0|00;" while it should show "IS 0600;". In this case
the K3 was set to CW mode. In LSB mode, the same window shows "CW 6+;"
where I presume it should have been "CW 60;". This damaged text shows
up in all windows (Rig received, K3 Com port, Power SCR-IF Aux CAT port,
etc.)
Attempted resolution includes reloading the K3 firmware and reloading
LPB from the website after clearing out all remnants of the old
program. Nothing helps - LPB still crashes when allowed to run for
several hours. Other programs not affected. Computer is on a UPS, so
momentary power outage would not be a cause (even if there should be one
every night!)
Clearly, there is a communication failure between the K3 and LPB, since
it occurs with nothing else connected. Is the problem with the K3, LBP
or the Win 7 operating system which sits between them? And what more
can I try to fix it?
Your thoughts will be greatly appreciated.
George, W3HBM
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to gkid...@ilstu.edu
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to gkid...@ilstu.edu
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to tom...@videotron.ca
---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com
