Joe, I'll comment on my setup:
1. Lock TX=RX is checked 2. tones are approximately 1500 hz Robie - AJ4F On Mon, Apr 17, 2017 at 1:34 AM, Joe Subich, W4TV <li...@subich.com> wrote: > > TX ad RX EQ are forced to flat in DATA A (and AFSK A) mode. > > What frequency tones (TX #### Hz in WSJT-X) are you using? Is WSJT-X > in split mode? > > If I adjust the audio input *carefully* to 4 bars, I will see the "ALC" > vary from 3 to 5 bars and the power output will vary between 98 and 102 > Watts (when set for 100 W). With the audio input adjusted to "4 bars > with the 5th flickering", I see marginally tighter power control - 99 > to 102 W. However, in no case is there a significant variation in the > power output. > > The *only time* power output is not as expected is if I am not using > split mode and trying to transmit with audio tones below 300 Hz or > above 2500 Hz (outside the DSP bandwidth). > > 73, > > ... Joe, W4TV > > > > On 4/16/2017 8:15 PM, Robie Elms wrote: > >> I also see the same behavior as Dave. I have verified my K3 is in DATA A >> and the TX Equalization is a flat line. However, I routinely make >> contacts with JT65. I use WSJT-x v 1.7.0 >> >> Robie - AJ4F >> >> On Mon, Apr 17, 2017 at 12:10 AM, Walter Underwood <wun...@wunderwood.org >> > >> wrote: >> >> TX EQ could cause problems like this if not in DATA A. >>> >>> wunder >>> K6WRU >>> Walter Underwood >>> CM87wj >>> http://observer.wunderwood.org/ (my blog) >>> >>> On Apr 16, 2017, at 4:52 PM, Joe Subich, W4TV <li...@subich.com> wrote: >>>> >>>> >>>> Since bars 0-4 represent audio drive level and *not* true ALC when >>>> in digital mode (DATA A, AFSK A), what you are seeing represents a >>>> >>> significant change in *audio drive level* for the different tones. >>> >>>> >>>> Are you sure you are using DATA A and not AFSK A with the AFSK >>>> Filter turned on? What frequency range are the tones? >>>> >>>> 73, >>>> >>>> ... Joe, W4TV >>>> >>>> >>>> On 4/16/2017 5:29 PM, Dave Hachadorian wrote: >>>> >>>>> I just started playing with JT-65 and JT-9 this weekend, and I’ve >>>>> >>>> already worked a bunch of DX, so it’s basically working ok. >>> >>>> >>>>> Transmitting on JT-65, I see a lot of variation in ALC and power as the >>>>> >>>> various tones change. I’m using Data A mode with the stock 2.7 >>> filter. I >>> just had a QSO with tone frequencies of about 1800 – 1950 Hz, and ALC >>> varied from zero to five bars on the different tones. Sound card output >>> is >>> about 50%, and Line In level is at 12. Is this variation normal, or am I >>> doing something wrong, and where should I set the ALC? >>> >>>> >>>>> Thanks. >>>>> >>>>> Dave Hachadorian, K6LL >>>>> Yuma, Arizona >>>>> >>>>> >>>>> >>>>> ______________________________________________________________ >>>>> Elecraft mailing list >>>>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>>>> Help: http://mailman.qth.net/mmfaq.htm >>>>> Post: mailto:Elecraft@mailman.qth.net >>>>> >>>>> This list hosted by: http://www.qsl.net >>>>> Please help support this email list: http://www.qsl.net/donate.html >>>>> Message delivered to li...@subich.com >>>>> >>>>> ______________________________________________________________ >>>> Elecraft mailing list >>>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>>> Help: http://mailman.qth.net/mmfaq.htm >>>> Post: mailto:Elecraft@mailman.qth.net >>>> >>>> This list hosted by: http://www.qsl.net >>>> Please help support this email list: http://www.qsl.net/donate.html >>>> Message delivered to wun...@wunderwood.org >>>> >>> >>> ______________________________________________________________ >>> Elecraft mailing list >>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>> Help: http://mailman.qth.net/mmfaq.htm >>> Post: mailto:Elecraft@mailman.qth.net >>> >>> This list hosted by: http://www.qsl.net >>> Please help support this email list: http://www.qsl.net/donate.html >>> Message delivered to rule...@gmail.com >>> >>> ______________________________________________________________ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:Elecraft@mailman.qth.net >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> Message delivered to li...@subich.com >> >> ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to rule...@gmail.com ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
