I have an 718 with the 250 Hz filter. That filter locks down things
quite well, but it also allows "blow by" with large nearby signals that
make things difficult also. In the short time I have been a CW op, the
skill that Ron mentions is just starting to get to me. I have often
been frustrated by other ops nearby. That is part of what drove me to
the K2, was the many choices of filters.
I agree with Scott, in the since, that I am seeking a way to make that
last filter have more isolation capability without further attenuating
the signal. Now that I have a little bit better idea what is going on
with Spectrogram, after I have all the pieces finished, I plan on making
another pass with that while sending some tones through and seeing what
kind of tweaking I can accomplish.
Scott, have you put your K2 through the Spectrogram alignments yet? I
was not terribly impressed with the filters after the default settings
were installed, but I was amazed after (several tries) I gave the
filters a good alignment with Spectrogram.
David Wilburn
[EMAIL PROTECTED]
K4DGW
K2 #5982
Ron D'Eau Claire wrote:
I can't speak about the 718 or the Elecraft DSP, but in my experience such
"brick wall" filtering creates far more problems than solutions. A huge
amount of unwanted stuff is produced by signals on the sharp edges of such a
filter that appear throughout the passband - much of it is that 'noise' you
mention.
I work 99% CW and my K2 is seldom set for less than 1.0 kHz bandwidth. My
minimum is 0.4 kHz used only when I get a "loudmouth" shouting from almost
on top of the signal I'm copying. That occasionally happens during a
contest, but that's about it.
I do have a skill that a great many experienced CW ops have that might be
the difference. We can copy easily with several signals within the passband.
It's like listening to one voice in a crowded party; we just "tune out" the
other babble going on around us unless it's something we want to follow. It
only gets difficult if one nut starts shouting in my ear when I'm trying to
listen to someone else, Hi!
Ron AC7AC
-----Original Message-----
Hello
I haven't had my K2 (# 5846 ) long enought to fully understand all the
different settings that are possible with it , so I have a question. My CW
filter setting are FL-1 1.50, FL-2 0.70, FL-3 0.40, and
FL-4 is 0.10. Even FL-4 is no where near as effective as the 250 hz crystal
filter in my Icom 718. When I turn on the 250 hz filter in the Icom, it's
like building a wall right on each side of the signal that I am listening
to. Nothing else is heard except noise and signals that are exactly on the
same frequency. Is this kind of selectivity possible with the K2? If I
installed the DSP option would that help? And if so, what would the filter
settngs need to be? The only options I presently have are the 160 meter
option, noise blanker, serial adapter, ssb option, and the KPA100. Thanks
Scott N5SM
_______________________________________________
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
_______________________________________________
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
_______________________________________________
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/subscribers.htm
Elecraft web page: http://www.elecraft.com
