Brett I do have all the slots filled with roofers and the FL1 in my case its an 8 poles 6.0 Khz,with that I am able to TX and RX on AM but not on FM,if you want to be able to use either AM or FM RX/TX you will have to purchase the FM filter of 13Khz BW.Hope this answer your doubt. AD4C K3 # 2192
"The difference between genius and stupidity is that genius has its limits".. -- Albert Einstein --- On Thu, 7/9/09, Brett Howard <br...@livecomputers.com> wrote: From: Brett Howard <br...@livecomputers.com> Subject: Re: [Elecraft] K3 Filter Question To: "Bob Cunnings" <bob.cunni...@gmail.com> Cc: elecraft@mailman.qth.net Date: Thursday, July 9, 2009, 6:20 AM I forgot to go back to that... I was thrown off by the comment on the order page that said you only need one of each filter for transmit. I know that doesn't fully say what I was hoping for though.... I wonder if there is any possibility of allowing AM TX and/or ESSB via the FM filter... As I'd like to have maximum flexibility but only have one slot left because of the way I have setup the radio for what I spend most of my time doing. Thanks for the assistance gentlemen. ~Brett On Thu, 2009-07-09 at 00:13 -0600, Bob Cunnings wrote: > Manual, pg 74: > > "Rule #1: If you plan to use a particular filter for both transmitting > and receiving (main receiver), you’ll need to > install it on the RF board. You can optionally install a filter of the > same or similar bandwidth on the sub > receiver for receive-only use. (This is recommended since it will keep > the receivers identical.)" > > Bob NW8L > > On Wed, Jul 8, 2009 at 11:31 PM, Brett Howard<br...@livecomputers.com> wrote: > > Ok so I'm curious if I'll be able to do what I'd like. I'd like to > > setup my K3 for maximum flexibility. At the moment I have these > > filters. > > > > 2.8Khz > > 1.8Khz > > 1Khz > > 250Hz > > > > These 4 filters are duplicated in the lower 4 slots of both receivers. > > I'd like to have the ability to do AM and FM both TX and RX in this > > radio. Can I add the AM filter and KBPF into the main RX and then put > > the FM filter into the KRX3? > > > > I'm hoping that I can then use the MainRX for broad frequency coverage > > and AM broadcast receive. Then if I ever want to do FM work I simply > > have to use the sub receiver to do so. Will TX through the FM filter > > work with it in the sub RX... To the best of my knowledge it appears > > that I can set the rig up in this fashion but that doesn't always mean > > it will work how I expect it to. > > > > Am I all wet here? > > > > Thanks > > > > ~Brett > > > > ______________________________________________________________ > > Elecraft mailing list > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:Elecraft@mailman.qth.net > > > > This list hosted by: http://www.qsl.net > > Please help support this email list: http://www.qsl.net/donate.html > > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html