On Saturday 18 November 2017 15:06:14 Chris Morley wrote: > ________________________________ > From: Gene Heskett <[email protected]> > Sent: November 18, 2017 5:33 PM > To: EMC developers > Subject: [Emc-developers] I'm bumfuzzled on video > > Greetings all; > > It appears that there is no longer any support for GTK+2 left in > wheezy, at least not that I can find and install, its GTK3 or do > without. > > I've found this page: > > <https://developer.gnome.org/gtk3/stable/gtk-migrating-2-to-3.html#id- >1.6.3.3.7> Migrating from GTK+ 2.x to GTK+ 3: GTK+ 3 Reference > Manual<https://developer.gnome.org/gtk3/stable/gtk-migrating-2-to-3.ht >ml#id-1.6.3.3.7> developer.gnome.org > GTK+ 3 is a major new version of GTK+ that breaks both API and ABI > compared to GTK+ 2.x, which has remained API- and ABI-stable for a > long time. > Then what do I need to install to make it work? > > > Gene > try this deb on wheezy: > > www.linuxcnc.org/dists/wheezy/base/binary-i386/glade-gtk2_3.8.0-0ubunt >u6_i386.deb<http://www.linuxcnc.org/dists/wheezy/base/binary-i386/glade >-gtk2_3.8.0-0ubuntu6_i386.deb> > I believe I have that on that machine, Chris, but gimme 5 to check. Yes, that been installed since the last time I tried to make it work, several months ago.
> <http://www.linuxcnc.org/dists/wheezy/base/binary-i386/glade-gtk2_3.8. >0-0ubuntu6_i386.deb> > > <http://www.linuxcnc.org/dists/wheezy/base/binary-i386/glade-gtk2_3.8. >0-0ubuntu6_i386.deb> Don't try to convert the GLADE file from one > version to the other. linuxcnc doesn't support GTK3 (which the newer > GLADE file use) > > Camview is is of course not officially supported by linuxcnc so I > don't guarantee this will fix your problem. > I do think people have experimented with another vision library - > opencv? Maybe some one can post some comments on that. > I have everything with libopencv in its name installed from my last attempt to do this. 25 of them. IP there a gui editor like glade for it? And I just found about 60 gtk2-engines that weren't installed, and it looks as if I should be using the glade-gnome for a gtk2 composer. Maybe I can get enough sensible bitches out of it to fix it. Installed them all. But I've been on the roof as one of my guy anchors has pulled out, and the wind is coming up. So I've cut 4 pieces of that composite decking, sank a hook in the middle of it, and 8 each 1/4" 2+ inch screws along the edge, gave the bottom of the first one a coat of white Black Jack, some sort of paddle it on with a putty knife sealer to fill the hollowed out bottom of the plastic decking, dropped it over the hole where a too small screw eye was. And despite its getting dark. managed to get the one loose guy wire loosely attached to the hook. More tomorrow, weather permiting. Its trying to rain but not getting much done, just a warm wind mostly. But I have to admit that I am not the man I once was, even once. Up and down the ladder several times about wiped out my legs. Muscles screaming for glucose, which I have a surplus of, but they also need insulin I don't have to make muscle food out of the glucose. Avoid getting old guys, its generally NOT fun. Thanks Chris, I'll see what this install fest produces and report later. But at 18:27, I'd better go feed my baby. > Chris M > ---------------------------------------------------------------------- >-------- Check out the vibrant tech community on one of the world's > most engaging tech sites, Slashdot.org! http://sdm.link/slashdot > _______________________________________________ > Emc-developers mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/emc-developers Cheers, Gene Heskett -- "There are four boxes to be used in defense of liberty: soap, ballot, jury, and ammo. Please use in that order." -Ed Howdershelt (Author) Genes Web page <http://geneslinuxbox.net:6309/gene> ------------------------------------------------------------------------------ Check out the vibrant tech community on one of the world's most engaging tech sites, Slashdot.org! http://sdm.link/slashdot _______________________________________________ Emc-developers mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-developers
