On Wednesday, January 26, 2022 4:08:17 PM EST Rod Webster wrote: > I have been using Bullseye for quite a while now but always install > from source which is pretty straightforward. > Like you, I found the existing Buster debs would not install. > > for Intel 64 bit hardware, these instructions now cover off on all of > the installation steps > https://www.qtpyvcp.com/install/bullseye.html > This will also install the qtvcp/qtpyvcp dependencies so pretty much > all sims will run. > > I did see that Bullseye PREEMPT_RT was available for the Pi and have > been meaning to give this a try. > I don't expect there will be any major changes.
I could not find a bullseye build in the waterfall page just now, where is it? > It really would be nice if the buildbot could be taught to build debs > for Bullseye so those that need master branch (eg any plasma user) > have a simple deb install pending the integration into Debian 12. > > Rod Webster > *1300 896 832* > +61 435 765 611 > Vehicle Modifications Network > www.vehiclemods.net.au > > On Thu, 27 Jan 2022 at 06:50, Steffen Möller <[email protected]> wrote: > > Hi Gene, > > > > On 26.01.22 02:27, gene heskett wrote: > > > Greetings all; > > > > > > I built a fresh pull of master earlier today, which makes > > > installable > > > debs. I normally run this shell script to install them, and on > > > buster it Just Works. > > > > And that is how things should also behave on Bullseye. Let's find out > > what is going wrong. > > > > > But, now I have succeeded in getting a raspios bullseye to run on a > > > 5.16.2-rt19-rt19-v7l+ #3 SMP PREEMPT_RT kernel, and that first boot > > > updated about 2gigs of stuff. There is about 130 pkgs to update. > > > > I have not run bullseye on a Raspberry, yet. I would however indeed > > go > > and update everything. > > > > sudo apt-get -u dist-upgrade > > > > should get you there. > > > > > And I've found a solution to the no net on boot problem applicable > > > to > > > home networks that are hosts file based. If you while the card is > > > still mounted in a reader, edit the /etc/dhcpdcp.conf file, you > > > will find a place at the bottom that is commented out but you can > > > uncomment it and fill in the data to fit your setup, and when > > > booted in the pi, just works, you have a network from the gitgo. > > > Thats one MAJOR headache out of the way. > > > > > > BUT, what I built on buster, will not install on bullseye as too > > > much has been version advanced. > > > > That is expected. > > > > > I have installed about a gig of stuff dpkg > > > complains about but have not been able to get a working install. > > > yet... > > > > > > The remaining errors are: > > > > > > dpkg: dependency problems prevent configuration of linuxcnc-uspace: > > > linuxcnc-uspace depends on libboost-python1.67.0; however: > > > Package libboost-python1.67.0 is not installed. > > > > > > linuxcnc-uspace depends on libpython3.7 (>= 3.7.0); however: > > > Package libpython3.7 is not installed. > > > > > > linuxcnc-uspace depends on python3 (<< 3.8); however: > > > Version of python3 on system is 3.9.2-3. > > > > > > linuxcnc-uspace depends on python3.7-tk; however: > > > Package python3.7-tk is not installed. > > > > > > linuxcnc-uspace depends on python3.7-numpy | python-numpy; however: > > > Package python3.7-numpy is not installed. > > > Package python-numpy is not installed. > > > > This raised some eyebrows on my end. Python 3.7 is history and > > dependencies are on Python3. A grep in the debian directory of what I > > have checked out from master does not have any notion of "3.7" in the > > debian folder. And python-numpy (without the "3") is a Python2 > > version, which is no longer needed. > > > > > But newer versions of all the above are all installed. > > > I do not know at this stage if I have enough to rebuild them as > > > yet. > > > The debhelper suite is not yet installed. > > > > > > So I need to see the /e/a/sources.list.d/linuxcnc.list file for > > > bullseye so I can see if those .debs will install. > > > > Something is off with your package. Please have a second look at when > > this package was built. Maybe it is an old one that was carried over > > from your past with Buster? > > > > Would you be prepared to try again? From scratch starting with a > > checkout of the master branch? See 10 minutes ago's post. > > > > Best, > > Steffen Thanks Rod Webster. Cheers, Gene Heskett. -- "There are four boxes to be used in defense of liberty: soap, ballot, jury, and ammo. Please use in that order." -Ed Howdershelt (Author, 1940) If we desire respect for the law, we must first make the law respectable. - Louis D. Brandeis Genes Web page <http://geneslinuxbox.net:6309/gene> _______________________________________________ Emc-developers mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-developers
