Computer is a Tualatin Celeron 1300MHz on a Soyo 7VBA-U, 512MB PC133 
Kingston VR and ATA133 40Gb Maxtor Hard Drive, with 3DFX Vodoo 3 16MB 
AGP video card.
Cable is 20cm length.

And i confirm the board is a 400K

Thanks again.


El 06/12/08 15:19, Peter C. Wallace escribió:
> On Sat, 6 Dec 2008, Richard Acosta wrote:
>
>> Date: Sat, 06 Dec 2008 15:12:32 -0200
>> From: Richard Acosta <[EMAIL PROTECTED]>
>> Reply-To: "Enhanced Machine Controller (EMC)"
>>     <emc-users@lists.sourceforge.net>
>> To: "Enhanced Machine Controller (EMC)" 
>> <emc-users@lists.sourceforge.net>
>> Subject: Re: [Emc-users] EMC 2.2.7 + 7i43 + Ted's sample,
>>     and same error than using EMC 2.2.6 + 7i43 + Ted's sample.... 
>> What now?
>>
>> i'l'l try the lights when at home and tell the exact order.
>> The port is an onboard port in a via mainboard
>
> Can you also tell me the motherboard type and cable length?
>
> I'm chasing some timing/ noise problems in the FPGA and CPLD code
> and duplicating your setup would be helpful here
>
>
>
>>
>> El 06/12/08 13:02, Peter C. Wallace escribió:
>>> On Sat, 6 Dec 2008, Richard Acosta wrote:
>>>
>>>> Date: Sat, 06 Dec 2008 03:14:13 -0200
>>>> From: Richard Acosta <[EMAIL PROTECTED]>
>>>> Reply-To: "Enhanced Machine Controller (EMC)"
>>>>     <emc-users@lists.sourceforge.net>
>>>> To: "Enhanced Machine Controller (EMC)"
>>>> <emc-users@lists.sourceforge.net>
>>>> Subject: Re: [Emc-users] EMC 2.2.7 + 7i43 + Ted's sample,
>>>>     and same error than using EMC 2.2.6 + 7i43 + Ted's sample....
>>>> What now?
>>>>
>>>> El 05/12/2008 07:35 p.m., Peter C. Wallace escribió:
>>>>> On Fri, 5 Dec 2008, Richard Acosta wrote:
>>>>> This may also indicate a inability to communicate with the card.
>>>>>
>>>>> 1. Is the card jumpered for EPP (W4 and W5 both in the 'down' 
>>>>> position)
>>>>>
>>>> Yes.
>>>>> 2. Is the card powered properly (all three status LEDS = RED RED
>>>>> YELLOW)
>>>>>     Should be on at power-up
>>>>>
>>>> Yes,
>>>>> 3. Is your parallel port set for EPP 1.9 mode?
>>>>>
>>>> Yes,
>>>>> 4. What kind of parallel cable do you have? We have done all of our
>>>>> testing
>>>>>     with Flat cable.
>>>>>
>>>> Flat cable, when starting EMC2 lights flash an ready goes on after 
>>>> about
>>>> 1 or 2sec
>>>>
>>>
>>> Ready?
>>>
>>> What lights change?
>>>
>>> There are three status lights on the 7I43: /DONE /INIT (both red) and
>>> POWER (Yellow)
>>>
>>>
>>> Also what type of parallel port do you have, Motherboard or PCI add-on?
>>>
>>>
>>>
>>>
>>>>
>>>> ------------------------------------------------------------------------------
>>>>  
>>>>
>>>>
>>>> SF.Net email is Sponsored by MIX09, March 18-20, 2009 in Las Vegas,
>>>> Nevada.
>>>> The future of the web can't happen without you.  Join us at MIX09 to
>>>> help
>>>> pave the way to the Next Web now. Learn more and register at
>>>> http://ad.doubleclick.net/clk;208669438;13503038;i?http://2009.visitmix.com/
>>>>  
>>>>
>>>>
>>>> _______________________________________________
>>>> Emc-users mailing list
>>>> Emc-users@lists.sourceforge.net
>>>> https://lists.sourceforge.net/lists/listinfo/emc-users
>>>>
>>>
>>> Peter Wallace
>>> Mesa Electronics
>>>
>>> (\__/)
>>> (='.'=) This is Bunny. Copy and paste bunny into your
>>> (")_(") signature to help him gain world domination.
>>> ------------------------------------------------------------------------ 
>>>
>>>
>>> ------------------------------------------------------------------------------
>>>  
>>>
>>> SF.Net email is Sponsored by MIX09, March 18-20, 2009 in Las Vegas, 
>>> Nevada.
>>> The future of the web can't happen without you.  Join us at MIX09 to 
>>> help
>>> pave the way to the Next Web now. Learn more and register at
>>> http://ad.doubleclick.net/clk;208669438;13503038;i?http://2009.visitmix.com/
>>>  
>>>
>>> ------------------------------------------------------------------------ 
>>>
>>>
>>> _______________________________________________
>>> Emc-users mailing list
>>> Emc-users@lists.sourceforge.net
>>> https://lists.sourceforge.net/lists/listinfo/emc-users
>>>
>>
>> ------------------------------------------------------------------------------
>>  
>>
>> SF.Net email is Sponsored by MIX09, March 18-20, 2009 in Las Vegas, 
>> Nevada.
>> The future of the web can't happen without you.  Join us at MIX09 to 
>> help
>> pave the way to the Next Web now. Learn more and register at
>> http://ad.doubleclick.net/clk;208669438;13503038;i?http://2009.visitmix.com/ 
>>
>> _______________________________________________
>> Emc-users mailing list
>> Emc-users@lists.sourceforge.net
>> https://lists.sourceforge.net/lists/listinfo/emc-users
>>
>
> Peter Wallace
> Mesa Electronics
>
> (\__/)
> (='.'=) This is Bunny. Copy and paste bunny into your
> (")_(") signature to help him gain world domination.
> ------------------------------------------------------------------------
>
> ------------------------------------------------------------------------------
> SF.Net email is Sponsored by MIX09, March 18-20, 2009 in Las Vegas, Nevada.
> The future of the web can't happen without you.  Join us at MIX09 to help
> pave the way to the Next Web now. Learn more and register at
> http://ad.doubleclick.net/clk;208669438;13503038;i?http://2009.visitmix.com/
> ------------------------------------------------------------------------
>
> _______________________________________________
> Emc-users mailing list
> Emc-users@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/emc-users
>   

------------------------------------------------------------------------------
SF.Net email is Sponsored by MIX09, March 18-20, 2009 in Las Vegas, Nevada.
The future of the web can't happen without you.  Join us at MIX09 to help
pave the way to the Next Web now. Learn more and register at
http://ad.doubleclick.net/clk;208669438;13503038;i?http://2009.visitmix.com/
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users

Reply via email to