Gene ,
this is with a 5i25 and 7i77 analog card ,

On 28 August 2014 15:29, David Armstrong <[email protected]> wrote:

> yes sorry gene in my haste yes it has full quad a b z
>
>
> On 28 August 2014 15:24, Gene Heskett <[email protected]> wrote:
>
>> On Thursday 28 August 2014 09:41:15 David Armstrong did opine
>> And Gene did reply:
>> > Guy's
>> > i'm having a problem trying to get a analog 10v spinde to scale
>> > correctly
>> >
>> > the spindle has a 1000 count encoder
>> > and gives a speed of 6200 rpm
>>
>> Thats good info but does go far enough. Does it do A/B/Z outputs in
>> quadrature format?
>>
>> At 1000ppr, thats an edge rate into the encoder module of a bit north of
>> 100 kilohertz at 6200 rpms.  If its quadrature A/B/Z output then that the
>> equ of slight more than 410 kilohertz rate for determining the encoders
>> position.
>>
>> This will absolutely preclude the use of a pure software approach thru the
>> parport.
>>
>> > now either i set the scale at 62
>> > and i get movement or what i thought was correct and get full speed and
>> > no change
>> >
>> > as i calculate if i am correct top speed 6200  so 10/6200 = 0.00161
>> > in my ini i have
>> >
>> > OUTPUT_SCALE = 0.00161
>> >
>> > i have not touched the scale setting in the hal file
>> > setp     scale.spindle.gain 60
>>
>> In most hal files this would be used to drive the tachometer graphic by
>> multiplying the encoders velocity output, usually in RPS, so it displays
>> RPM.
>>
>> > setp     lowpass.spindle.gain 1.000000
>>
>> And this would be set at a much smaller value to steady the graphic
>> tachometer.  Otherwise the needle is so bouncy its hard to follow, or if
>> using the bar graph version, the last 2 digits of the rpm displayed are so
>> random as to be a bit un-nerving because you just know, with the mass of
>> the chuck and all, it can't possibly be changing its speed by a hundred or
>> more rpms 10x a second which is the usual display update rate.  So we need
>> more info before we can do much more than make SWAG's about what you'll
>> need to do.
>>
>> > which i dont think i need so ,
>> > so just becoming confused
>> >
>> > any guidance please
>>
>> I will, in the next day or 4, be getting all this built and sorted, using
>> one of the Pico Systems PWM driven servo amplifiers to run the spindle on
>> my 7x12, using a Mesa 5i25 card without any accessory cards attached.  So
>> that obviously will color what I have to say.  Someone else, using
>> different hardware from mine will probably have totally different ideas
>> about how to go about calibrating this.
>>
>> > Dave
>> > -----------------------------------------------------------------------
>> > ------- Slashdot TV.
>> > Video for Nerds.  Stuff that matters.
>> > http://tv.slashdot.org/
>> > _______________________________________________
>> > Emc-users mailing list
>> > [email protected]
>> > https://lists.sourceforge.net/lists/listinfo/emc-users
>>
>>
>> Cheers, Gene Heskett
>> --
>> "There are four boxes to be used in defense of liberty:
>>  soap, ballot, jury, and ammo. Please use in that order."
>> -Ed Howdershelt (Author)
>> Genes Web page <http://geneslinuxbox.net:6309/gene>
>> US V Castleman, SCOTUS, Mar 2014 is grounds for Impeaching SCOTUS
>>
>>
>> ------------------------------------------------------------------------------
>> Slashdot TV.
>> Video for Nerds.  Stuff that matters.
>> http://tv.slashdot.org/
>> _______________________________________________
>> Emc-users mailing list
>> [email protected]
>> https://lists.sourceforge.net/lists/listinfo/emc-users
>>
>
>
------------------------------------------------------------------------------
Slashdot TV.  
Video for Nerds.  Stuff that matters.
http://tv.slashdot.org/
_______________________________________________
Emc-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/emc-users

Reply via email to