interesting AGie stuff please look at http://www.gfms.com/content/dam/gfac/proddb/edm/die-sinking/en/agiecharmilles-form-200-ms_en.pdf for a bit more screenshots remember, this is for a proprietary machine, and will be of limited use what is good though, is they actualy asked users to evaluate the user interface before forcing it onto all the users GF is George FIscher, the auto body company, ( and a lot more) they bought up AGie Charmilles Elox and other edm mfctrs over the years (the borg of edm, so they have acquired a LOT of edm knowledge )
i was head of AGie sink edm for a while back in the day, sort of by default, no one else knew what the hell those machine were, and they only wanted to play on wedm anyway (eeeoooow its oily and dirty eeeooooow) regards TomP tjtr33 On 12/26/16 19:46, Nicklas Karlsson wrote: >> ... >> please tell us more of what you try to control with all those flushing >> controls! >> it seems there is magnitude of flush, and type of flush(pressure / >> vacuum), and tank fill and dump > The flushing controls are coils I found inside the machine and I have not yet > figured out how to use them. I added a button so I could turn them off/on, > there are also a few LEDs with no use. I think lubrification should be > started then machine is enabled? > > It is possible to adjust tOff/tOn time and a meter for gap voltage, there are > few buttons left over from example. I spent a just a few hours on the user > interface and are right now thinking about how it should look and more or > less standard *-codes for parameters for generator, I also have found m-codes > you sent earlier. > > > I have found Charmilles have a new standard user interface > http://www.mfgnewsweb.com/archives/4/37497/Controls-dec12/New-Standard-User-Interface-for-Sinker-EDM-Machines.aspx > > >> the area 'Settings' could be anything from on & off time to >> cuttime/jumpdistance/frequency. >> the 'Command' area is understandable >> regards, & merry Christmas >> tomp tjtr33 >> On 12/25/16 21:54, Nicklas Karlsson wrote: >>>>> Happen to know any more or less g-codes for these motions? g-codes >>>>> for control of flush? g-codes for control of EDM power source? >>>> ... i uploaded mcodes before with python commands to change edm >>>> generator on/off/current/polarity >>> I could remember I god some g-code suitable for EDM and are looking >>> for them right now. I have entered g-code for Linuxcnc and Sodick wire >>> EDM in a database, there a problem with a few codes. The database >>> could be rather useful if filled in for more machines and put on the >>> web. I have never machined run a machine and think it could be a good >>> start to read thru which codes are available. >>> ------------------------------------------------------------------------------ >>> Developer Access Program for Intel Xeon Phi Processors Access to Intel >>> Xeon Phi processor-based developer platforms. With one year of Intel >>> Parallel Studio XE. Training and support from Colfax. Order your >>> platform today.http://sdm.link/intel >>> _______________________________________________ Emc-users mailing list >>> Emc-users@lists.sourceforge.net >>> https://lists.sourceforge.net/lists/listinfo/emc-users >> ------------------------------------------------------------------------------ >> Developer Access Program for Intel Xeon Phi Processors >> Access to Intel Xeon Phi processor-based developer platforms. >> With one year of Intel Parallel Studio XE. >> Training and support from Colfax. >> Order your platform today.http://sdm.link/intel >> _______________________________________________ >> Emc-users mailing list >> Emc-users@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/emc-users > > > > ------------------------------------------------------------------------------ > Developer Access Program for Intel Xeon Phi Processors > Access to Intel Xeon Phi processor-based developer platforms. > With one year of Intel Parallel Studio XE. > Training and support from Colfax. > Order your platform today.http://sdm.link/intel > > > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users ------------------------------------------------------------------------------ Developer Access Program for Intel Xeon Phi Processors Access to Intel Xeon Phi processor-based developer platforms. With one year of Intel Parallel Studio XE. Training and support from Colfax. Order your platform today.http://sdm.link/intel _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
