On Friday 13 October 2017 11:09:33 Peter C. Wallace wrote: > On Fri, 13 Oct 2017, andy pugh wrote: > > Date: Fri, 13 Oct 2017 15:53:52 +0100 > > From: andy pugh <[email protected]> > > Reply-To: "Enhanced Machine Controller (EMC)" > > <[email protected]> > > To: "Enhanced Machine Controller (EMC)" > > <[email protected]> Subject: Re: [Emc-users] For Peter > > C. Wallace > > > > On 13 October 2017 at 15:43, Gene Heskett <[email protected]> > > wrote: > > > > Plugging a new(er, I don't recall if it was programmed) 5i25 card > > in, dmesg says it found a xxxx:5125 card. Sounds like a blown pci > > bus line. OTOH, TLMonster has a 5i25 in it, and it says its a 5125 > > too. And its working ok. False Flag? > > 5125 is just a numerical version of 5i25 in a field which is numeric. > > Doesn't look like it can be a single PCI line. > > 1 = 0011001 > i = 01101001 > I = 01001001
And I can't reply to Peters addition because its below Andy's dash dash space \n sig separator. So I'll copy/paste >The VID:DID for a 5I25 is >2718:5125 IIRC thats the correct of what I saw on screen, but I'll have to go plug a 5i25 back into it. Did, yes, correct. >If you can read this its likely the PCI bus is OK >Another clue to PCI bus issues is if LinuxCNC doesnt find the correct >HM2 cookie = >0x55AACAFE Can't test for this locally, no keyboard or mouse, but I'll go put a card in and try it from here with an ssh login. brb. verified card had prob_rfx2.pin in it, put it in machine, powered up, collected coffee cup, and filled it on way back to this chair. Linuxcnc -l runs, only fuss is a gladeXML incomplete message. so let me go power up the main machines psu & see if it will home. Yes, and I can jog it from here. These are all the fusses I got in the login screen from here: gladevcp: auxiliary dir: /usr/share/linuxcnc/aux_gladevcp/NativeCAM gladevcp: importing: /usr/share/linuxcnc/aux_gladevcp/NativeCAM/pref_edit.py gladevcp: importing: /usr/share/linuxcnc/aux_gladevcp/NativeCAM/ncam.py (gladevcp:3704): libglade-WARNING **: Expected <glade-interface>. Got <interface>. (gladevcp:3704): libglade-WARNING **: did not finish in PARSER_FINISH state **** GLADE VCP ERROR: With xml file: camview.glade : could not create GladeXML object And I don't recall that I am using camview.glade! However I was last working on making the camera work, as an edge detector yadda yadda. So its possibly gotten into the mix. But where the heck is my local keyboard and mouse?, neither works after a login and only the keyboard works on the login greeter. And I have not played with what was a working configuration in re that in months. I'll go give that connector that may have shorted to that relay box, a coat of Go-2, aka goop, over the end face of the ribbon cable to help prevent that potential short again. I'll take the mouse and its button to the lathe and verify it works there. Or across to the other dell I use for mesaflashing to see if it works there. Back later with any more news about this headache. Thanks Peter, it helps if you name the tree I'm looking for. :) >Peter Wallace Cheers, Gene Heskett -- "There are four boxes to be used in defense of liberty: soap, ballot, jury, and ammo. Please use in that order." -Ed Howdershelt (Author) Genes Web page <http://geneslinuxbox.net:6309/gene> ------------------------------------------------------------------------------ Check out the vibrant tech community on one of the world's most engaging tech sites, Slashdot.org! http://sdm.link/slashdot _______________________________________________ Emc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/emc-users
