Chok di pi mail! Happy New Year to all. TomP On Mon, Dec 30, 2019, 11:59 PM Dave Matthews <n36...@gmail.com> wrote:
> For some reason I didn't get that to work. Looking at what did work > it should have. I may not have hit save or something. > > I found this link on the LinuxCNC > forumshttps:// > forum.linuxcnc.org/9-installing-linuxcnc/35839-updating-to-latest-version-of-2-8?start=20 > and with a couple tweaks now have 2.8 installed. His instructions > have an error in Step 2. The lines need to start with http:// > > The machine is now happily running 2 instances of glxgears and > streaming from Youtube. > > Latency test is showing max jitter of 45687 on Servo and 40422 on > Base. That is with the onboard video. I may drop a card in and see > if I can get it better but that is probably more than adequate for my > Gatton CNC on a parallel port. I am running it at 3200 > microsteps/inch and don't need over 100 ipm for my purposes. > > Dave > > On Sun, Dec 29, 2019 at 9:32 PM Phillip Carter <phillcarte...@gmail.com> > wrote: > > > > I am not sure when it will be released, it can't be too far away. > > > > You should be good to go using the 2.7-rtpreempt changed to > 2.8-rtpreempt. > > > > You could also download the the latest package from > http://buildbot.linuxcnc.org/dists/stretch/2.8-rtpreempt/ < > http://buildbot.linuxcnc.org/dists/stretch/2.8-rtpreempt/> and install it > directly. > > > > > On 30 Dec 2019, at 1:17 pm, Dave Matthews <n36...@gmail.com> wrote: > > > > > > I'll give it a try in the morning. That page could use a bit of > updating. > > > I found a few other options to try also. Any idea when 2.8 will be the > > > default install? It looks like it has been stable for quite a while. > > > > > > Dave > > > > > > On Sun, Dec 29, 2019, 21:11 Phillip Carter <phillcarte...@gmail.com> > wrote: > > > > > >> I think it may be sudo apt-get install linuxcnc-uspace > > >> > > >>> On 30 Dec 2019, at 12:53 pm, Dave Matthews <n36...@gmail.com> wrote: > > >>> > > >>> On Mon, Dec 30, 2019 at 12:11 AM Phillip Carter < > phillcarte...@gmail.com> > > >> wrote: > > >>>> > > >>>> > > >>>>> I installed the dependency fail for the sudo apt-key adv > --keyserver > > >>>>> hkp://keys.gnupg.net --recv-key EF1B07FEE0EE663E step. When I > try to > > >>>>> install the key I get: > > >>>>> Executing: /tmp/apt-key-gpghome.RJo9NWtHgB/gpg.1.sh --keyserver > > >>>>> hkp://keys.gnupg.net --recv-key EF1B07FEE0EE663 > > >>>>> gpg: "EF1B07FEE0EE663" not a key ID: skipping > > >>>>> > > >>>> you are missing the "E" at the end > > >>> Added the E and reran the command. It worked. I think I got it to > > >>> work before that but blew it on the retry of the command. > > >>> > > >>>> > > >>>> > > >>>>> and there is no /etc/apt/sources.list.d/linuxcnc-buildbot.list > created. > > >>>>> > > >>>>> I created the file and added the 2.7 entries and edited them to > 2.8. > > >>>>> That got me an install of the 2.8 docs but nothing else. > > >>>>> > > >>>>> I don't remember what incantations I did to install 2.8 on the old > > >>>>> machine. I think it was just pointing at repositories and using > > >>>>> apt-get. > > >>>>> > > >>>> if you created /etc/apt/sources.list.d/linuxcnc-buildbot.list then > > >> check your /etc/apt/sources.list file and comment out any lines that > > >> reference linuxcnc > > >>> > > >>> No references in /etc/apt/sources.list. I tried commenting them out > > >>> in /etc/apt/sources.list.d/linuxcnc-list but no change. > > >>> > > >>> I tried using the 2.7 entries replacing the 7 with 8 and also tried > > >>> pointing to Master with no luck. > > >>> deb http://buildbot.linuxcnc.org/ stretch master-rtpreempt > > >>> deb-src http://buildbot.linuxcnc.org/ stretch master-rtpreempt > > >>> > > >>> cncuser@localhost:/etc/apt/sources.list.d$ cat linuxcnc.list > > >>> deb http://linuxcnc.org/ stretch base > > >>> #deb-src http://linuxcnc.org/ stretch base > > >>> deb http://linuxcnc.org/ stretch 2.7-uspace > > >>> #deb-src http://linuxcnc.org/ stretch 2.7-uspace > > >>> #deb http://buildbot.linuxcnc.org/ stretch 2.7-rtpreempt > > >>> #deb-src http://buildbot.linuxcnc.org/ stretch 2.7-rtpreempt > > >>> > > >>> cncuser@localhost:/etc/apt/sources.list.d$ cat linuxcnc.list > > >>> deb http://linuxcnc.org/ stretch base > > >>> #deb-src http://linuxcnc.org/ stretch base > > >>> deb http://linuxcnc.org/ stretch 2.7-uspace > > >>> #deb-src http://linuxcnc.org/ stretch 2.7-uspace > > >>> #deb http://buildbot.linuxcnc.org/ stretch 2.7-rtpreempt > > >>> #deb-src http://buildbot.linuxcnc.org/ stretch 2.7-rtpreempt > > >>> > > >>> cncuser@localhost:/etc/apt/sources.list.d$ sudo apt-get update > > >>> Ign:1 http://ftp.debian.org/debian stretch InRelease > > >>> Hit:2 http://security.debian.org/debian-security stretch/updates > > >> InRelease > > >>> Ign:3 http://linuxcnc.org stretch InRelease > > >>> Ign:4 http://buildbot.linuxcnc.org stretch InRelease > > >>> Hit:5 http://ftp.debian.org/debian stretch Release > > >>> Hit:7 http://linuxcnc.org stretch Release > > >>> Hit:8 http://buildbot.linuxcnc.org stretch Release > > >>> Reading package lists... Done > > >>> cncuser@localhost:/etc/apt/sources.list.d$ sudo apt-get install > linuxcnc > > >>> Reading package lists... Done > > >>> Building dependency tree > > >>> Reading state information... Done > > >>> Package linuxcnc is not available, but is referred to by another > package. > > >>> This may mean that the package is missing, has been obsoleted, or > > >>> is only available from another source > > >>> > > >>> E: Package 'linuxcnc' has no installation candidate > > >>> > > >>> > > >>> Anyplace I can just grab an iso and install it or the correct entries > > >>> for /etc/apt/sources.list. or do I need to grab the sources and > > >>> build? The buildbot page instructions are way out of date. > > >>> > > >>> Dave > > >>> > > >>> > > >>> _______________________________________________ > > >>> Emc-users mailing list > > >>> Emc-users@lists.sourceforge.net > > >>> https://lists.sourceforge.net/lists/listinfo/emc-users > > >> > > >> > > >> > > >> _______________________________________________ > > >> Emc-users mailing list > > >> Emc-users@lists.sourceforge.net > > >> https://lists.sourceforge.net/lists/listinfo/emc-users > > >> > > > > > > _______________________________________________ > > > Emc-users mailing list > > > Emc-users@lists.sourceforge.net > > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > > > _______________________________________________ > > Emc-users mailing list > > Emc-users@lists.sourceforge.net > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users > _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
