A 2x6 antenna switch for so2r should work great for this. Check out the kit from KK1L.
73 Greg AB7R On Aug 12, 2012 7:52 AM, "Ken Buser" <[email protected]> wrote: > Thanks Tim, > In my mind I was trying to associate a SCU with a path from a Specific > SO239 Connection, > Your Wording of "Transceiver Port" Helps clear that up. > I should have know this thing was more "Flexable" than that. > > I still need the ability to switch multipal antennas to either of the > transceiver ports. I think the unit I am building > will help in that area. > > Thanks again for the reply. > > Ken W9IE > > ----- Original Message ----- > From: Tim Ellison > To: Ken Buser ; [email protected] > Sent: Sunday, August 12, 2012 8:50 AM > Subject: Re: [FlexEdge] 6000 Series Antenna Questions > > > Ken, > > The internal ATU is only in the TX signal chain, so it is not connected > to either SCU. Remember, the SCU is a wide band RF spectrum ADC, so if you > are transmitting on one frequency, you still have the ability to receive on > the other slice receivers defined on that SCU or other SCU in the case of > the FLEX-6700. > > There are (2) SO-239 transceiver connectors on both the FLEX-6500 and > the FLEX-6700. The FLEX-6500 has one RX in/out loop that can be assigned > to it's SCU and the FLEX-6700 has two RX in/out loops for it's two SCUs. > SCUs can be assigned to a RX only or a transceiver port. > > I suspect that the manual will not be available until the software is > available. > > In regards to the needed "Support Group" to help manage SWS (SDR > Withdrawal Syndrome), we have been selling a few FLEX-1500s to help bridge > the gap. ;-) > > > Tim Ellison > On 8/11/2012 12:07 PM, Ken Buser wrote: > > To Tim, or someone at Flex > > I have on order a Flex 6700 and am planning for what I believe will be > necessary in the order of external Antenna switching. > > I have designed and am in the process of building an Antenna Matrix which > will allow for any of 5 Antennas to be connected to either of the 2 SCU's. > There will be Pic Processor control which will stop any invalid > connection, Like more than 2 Antennas selected or more than one connected > to the same SCU. > > My External Antenna Tuner, Amp, and Power Master unit can be put in > line with either of the SCU's. or not used at all. > > In the process I started thinking about the Internal ATU..... > > Can it be used with either SCU ??? > > Will it keep settings if I were to switch transmitt from one SCU to the > other on different Bands ? > > Also I assume the 6500 only has one SO239 connector on its SCU on the > rear.... > > Will we be able to see a Manual some time before the first units start > shipping in Q4 ?? > > I think we need a support group for those of us that have sold their > Flex's and are now FlexLess until the new 6000 series arrives hi hi > > 73's Ken W9IE > _______________________________________________ > Flexedge mailing list > [email protected] > http://mail.flex-radio.biz/mailman/listinfo/flexedge_flex-radio.biz > This is the FlexRadio Systems e-mail Reflector called FlexEdge. It is > used for posting topics related to SDR software development and > experimentalist who are using beta versions of the software. > > _______________________________________________ > Flexedge mailing list > [email protected] > http://mail.flex-radio.biz/mailman/listinfo/flexedge_flex-radio.biz > This is the FlexRadio Systems e-mail Reflector called FlexEdge. It is > used for posting topics related to SDR software development and > experimentalist who are using beta versions of the software. > _______________________________________________ Flexedge mailing list [email protected] http://mail.flex-radio.biz/mailman/listinfo/flexedge_flex-radio.biz This is the FlexRadio Systems e-mail Reflector called FlexEdge. It is used for posting topics related to SDR software development and experimentalist who are using beta versions of the software.
