That I've done. Port enabling I know. I'm just completely stumped. -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Jason Pope Sent: Friday, February 20, 2009 10:08 AM To: Chuck Ufarley Cc: [email protected] Subject: Re: [f-nsp] Port state blocking?
I think you need to enable the port. jp On Fri, Feb 20, 2009 at 11:51 AM, Chuck Ufarley <[email protected]> wrote: > This might be a silly question, but I can't get a port to come up on a > ServerIron. I enabled the interface and connected it properly to a > FES-X2402 switch, but the J-B16GC and the J-B2Gx ports just won't come up > and forward. The cards have worked in other configs, but I can't get > anything to come out of "blocking" mode. Here are the shows (any help > greatly appreciated): > > ServerIronGT E-1#sho run > !Building configuration... > !Current configuration : 378 bytes > ! > ver 11.0.00TD4 > ! > module 1 bi-0-port-wsm6-management-module > module 3 bi-jc-2-port-gig-module > module 4 bi-jc-16-port-gig-copper-module > ! > context default > ! > aaa authentication web-server default local > no enable aaa console > telnet server > username admin password ..... > snmp-server > ! > interface ethernet 4/9 > ip address 192.168.0.77 255.255.255.0 > ! > end > > ServerIronGT E-1#sho run > !Building configuration... > !Current configuration : 378 bytes > ! > ver 11.0.00TD4 > ! > module 1 bi-0-port-wsm6-management-module > module 3 bi-jc-2-port-gig-module > module 4 bi-jc-16-port-gig-copper-module > ! > context default > ! > aaa authentication web-server default local > no enable aaa console > telnet server > username admin password ..... > snmp-server > ! > interface ethernet 4/9 > ip address 192.168.0.77 255.255.255.0 > ! > end > > ServerIronGT E-1#sho mod > Module Status Ports Starting MAC > S1: B0GMR WSM6 Management Module, SYSIF 2 M6, ACTIV 0 > S2: > S3: J-BxG2 JetCore Gig Fiber Module, SYSIF OK 2 000c.dbb5.b640 > S4: J-BxGC16 JetCore Gig Copper Module, SY OK 16 000c.dbb5.b660 > ServerIronGT E-1#sho int e 4/9 > GigabitEthernet4/9 is down, line protocol is down > Hardware is GigabitEthernet, address is 000c.dbb5.b668 (bia > 000c.dbb5.b668) > Configured speed auto, actual unknown, configured duplex fdx, actual > unknown > Member of L2 VLAN ID 1, port is untagged, port state is BLOCKING > STP configured to ON, priority is level0, flow control enabled > mirror disabled, monitor disabled > Not member of any active trunks > Not member of any configured trunks > No port name > Internet address is 192.168.0.77/24, MTU 1518 bytes, encapsulation > ethernet > 300 second input rate: 0 bits/sec, 0 packets/sec, 0.00% utilization > 300 second output rate: 0 bits/sec, 0 packets/sec, 0.00% utilization > 991 packets input, 77378 bytes, 0 no buffer > Received 581 broadcasts, 410 multicasts, 0 unicasts > 0 input errors, 0 CRC, 0 frame, 0 ignored > 0 runts, 0 giants, DMA received 0 packets > 0 packets output, 0 bytes, 0 underruns > Transmitted 0 broadcasts, 0 multicasts, 0 unicasts > 0 output errors, 0 collisions, DMA transmitted 0 packets > ServerIronGT E-1# > > +++++ > > Thanks much, everyone. > > _______________________________________________ > foundry-nsp mailing list > [email protected] > http://puck.nether.net/mailman/listinfo/foundry-nsp > _______________________________________________ foundry-nsp mailing list [email protected] http://puck.nether.net/mailman/listinfo/foundry-nsp No virus found in this incoming message. Checked by AVG - www.avg.com Version: 8.0.233 / Virus Database: 270.10.22/1946 - Release Date: 02/11/09 11:13:00 _______________________________________________ foundry-nsp mailing list [email protected] http://puck.nether.net/mailman/listinfo/foundry-nsp
