Let me look at the release notes and I will unicast you back.
Mike On Jan 7, 2011 5:29 PM, "Joseph Hardeman" <[email protected]> wrote: > Hey Mike, > > You wouldn't happen to know what version of code or when they started > supporting dynamic LACP over tagged links would be would you? > > Joe > > On 1/7/2011 8:15 PM, Mike Allen wrote: >> Joe, Scott is likely on the right track. Early versions of B4000/8000 >> code did not support dynamic LACP over tagged links. Given that, your >> options are upgrading to a newer release, or use static trunks as you >> mentioned. If you do the upgrade and then do LACP over a tagged port, >> make sure you use a LACP key. Other than that, it should work just >> fine between vendors. Hope that helps. >> Mike >> >> On Fri, Jan 7, 2011 at 4:53 PM, Joseph Hardeman <[email protected] >> <mailto:[email protected]>> wrote: >> >> >> >> On 1/7/2011 7:36 PM, Big Wave Dave wrote: >> >> On Fri, Jan 7, 2011 at 4:27 PM, Joseph >> Hardeman<[email protected] <mailto:[email protected]>> >> wrote: >> >> Hi Everyone, >> >> I am having a bit of an issue, I have gotten a pair of >> Cisco 6509's with the >> SUP-720 engines. I am trying to configure link >> aggregation between one of >> these to a BI4000 I have to test with before we put them >> into production and >> connect them to our BI8000's and fight this problem then. >> I have been >> searching and looking at the docs I have. The >> configuration I have on the >> Cisco's allow them to talk over the port channels between >> each other with no >> issues. >> >> I can setup the command "link-aggregation active" on port >> "ethe 1/5" with no >> issues it takes the command, but when I go to add a test >> VLAN on to that >> port I get the following error message: >> >> error - some ports are running LACP and can not be tagged >> ports. >> >> Here is the command I am running on the BI: >> >> test(config)#int e 1/5 >> test(config-if-e1000-1/5)#link-aggregate configure key 10000 >> test(config-if-e1000-1/5)#link-aggregate active >> test(config-if-e1000-1/5)#exit >> test(config)#vlan 14 >> test(config-vlan-14)#tagged e 1/5 >> error - some ports are running LACP and can not be tagged >> ports. >> test(config-vlan-14)#end >> >> Here is the output of sh int e 1/5" >> GigabitEthernet1/5 is up, line protocol is up >> Hardware is GigabitEthernet, address is 00e0.52cc.3b04 >> (bia 00e0.52cc.3b04) >> Configured speed 1Gbit, actual 1Gbit, configured duplex >> fdx, actual fdx >> Member of L2 VLAN ID 1, port is untagged, port state is >> BLOCKING >> STP configured to ON, priority is level0, flow control >> disabled >> mirror disabled, monitor disabled >> Not member of any active trunks >> Not member of any configured trunks >> No port name >> MTU 1518 bytes, encapsulation ethernet >> 300 second input rate: 40104 bits/sec, 72 packets/sec, >> 0.00% utilization >> 300 second output rate: 0 bits/sec, 0 packets/sec, 0.00% >> utilization >> 899789 packets input, 62419802 bytes, 0 no buffer >> Received 372 broadcasts, 899417 multicasts, 0 unicasts >> 0 input errors, 0 CRC, 0 frame, 0 ignored >> 0 runts, 0 giants, DMA received 899786 packets >> 0 packets output, 0 bytes, 0 underruns >> >> > Transmitted 0 broadcasts, 0 multicasts, 0 unicasts >> >> 0 output errors, 0 collisions, DMA transmitted 0 packets >> >> >> Output of sh link-aggregation: >> Long timeout: 90, default: 90 >> Short timeout: 3, default: 3 >> Port [Sys P] [Port P] [ Key ] >> [Act][Tio][Agg][Syn][Col][Dis][Def][Exp][Ope] >> 1/5 1 1 0 Yes S Agg Syn Col >> Dis Def No Blo >> >> >> So my question is what am I missing here? From >> everything I found, all I >> have to do after setting 1 or more ports into a >> link-aggregation is to add >> the VLAN's as tagged to the ports with the same key. But >> its not allowing >> me to add the tagged vlans. >> >> Any suggestions? >> >> Thanks >> >> Joe >> _______________________________________________ >> >> >> I've had similar problems before. >> My bookmark takes me to: >> >> http://www.techsneeze.com/create-vlan-trunk-between-cisco-ios-and-foundry-bigiron >> >> Dave >> >> Hi Dave >> >> Thanks for the link, but its only showing how to tag a vlan to the >> port, which what I am currently doing but with the new ciscos and >> adding more fiber between our routers and switches I wanted to be >> able to do link aggregation. I am guessing I can't with this >> system unless I go with Trunk mode. >> >> Joe >> >> _______________________________________________ >> foundry-nsp mailing list >> [email protected] <mailto:[email protected]> >> http://puck.nether.net/mailman/listinfo/foundry-nsp >> >>
_______________________________________________ foundry-nsp mailing list [email protected] http://puck.nether.net/mailman/listinfo/foundry-nsp
