Now issue CP Q MDISK USER LINUX02 0100 DIRECT LOCATION to see what is in the active CP directory
2008/3/19, Vikesh Bhoola <[EMAIL PROTECTED]>: > NB: This email and its contents are subject to our email legal notice > which can be viewed at http://www.sars.gov.za/Email_Disclaimer.pdf > > ---- > Many thanks to all that responded. > > I should have mentioned that I had confirmed that LNX000 is a Model-9. > > Below confirms the DEVTYPE & number of cylinders for LNX000 is that of a > Mod-9 : > > Q DASD LNX000 > > DASD 7E7D CP SYSTEM LNX000 0 > Ready; T=0.01/0.01 09:56:45 > > > Q DASD DETAILS 7e7d > > 7E7D CUTYPE = 2105-E8, DEVTYPE = 3390-0C, VOLSER = LNX000, CYLS = 10017 > > CACHE DETAILS: CACHE NVS CFW DFW PINNED CONCOPY > > -SUBSYSTEM Y Y Y - N N > > -DEVICE Y - - Y N N > > DEVICE DETAILS: CCA = 7D, DDC = -- > > DUPLEX DETAILS: -- > > CU DETAILS: SSID = 015E, CUNUM = 7E00 > > Ready; T=0.01/0.01 09:57:16 > > > The problem still persists. > > Any further suggestions as what I'm possibly missing.. > > Kind Regards, > Vikesh Bhoola > > > -----Original Message----- > From: The IBM z/VM Operating System [mailto:[EMAIL PROTECTED] On > Behalf Of Bruce Hayden > Sent: 18 March 2008 05:30 PM > To: IBMVM@LISTSERV.UARK.EDU > Subject: Re: Mdisk 3390 Model 9 dasd > > From the MAINT id, enter Q DASD LNX000. This will give you the device > address of that volume, such as: > DASD 6903 CP SYSTEM LNX000 > Then enter Q DASD DETAILS nnnn and find out how many cylinders CP > thinks it has. If it is incorrect, it isn't configured correctly in > the storage controller or you have the wrong address. > > On Tue, Mar 18, 2008 at 11:18 AM, Vikesh Bhoola <[EMAIL PROTECTED]> > wrote: > > NB: This email and its contents are subject to our email legal notice > > which can be viewed at http://www.sars.gov.za/Email_Disclaimer.pdf > > > > ---- > > Good day, > > Firstly, apologies for a very basic question from a z/OS system > > programmer. > > > > Not being a VM expert, I've been struggling with this for most of the > > day and was hoping someone could perhaps help while I'm still > > downloading the manuals. > > > > I am busy with the zLINUX installation on zVM. > > I would like to make use of 3390 Model 9 disk for the Linux software. > We > > would like to make use of a bit more space (over 3338 cyl or 2.7Gb) > and > > hence have the following definitions in USER DIRECT : > > > > USER LINUX02 LNX4VM 512M 2G G > > INCLUDE LINDFLT > > OPTION APPLMON > > MDISK 100 3390 0001 4500 LNX000 MR LNX4VM LNX4VM LNX4VM > > MDISK 102 3390 4501 0300 LNX000 MR LNX4VM LNX4VM LNX4VM > > MDISK 103 3390 4801 3038 LNX000 MR LNX4VM LNX4VM LNX4VM > > MDISK 104 3390 7839 2177 LNX000 MR LNX4VM LNX4VM LNX4VM > > > > When I logon to LINUX02, I get the following msg : > > LOGON LINUX02 > > > > HCPLNM1151E LINUX02 0100 has not been linked because it is not within > CP > > volume extents. > > > > HCPLNM1151E LINUX02 0102 has not been linked because it is not within > CP > > volume extents. > > > > HCPLNM1151E LINUX02 0103 has not been linked because it is not within > CP > > volume extents. > > > > HCPLNM1151E LINUX02 0104 has not been linked because it is not within > CP > > volume extents. > > > > > > > > Searching on this msg does not provide any clues how to specify that > > this is a 3390 Model 9 dasd. > > > > Your assistance is very much appreciated. > > > > Kind Regards, > > Vikesh Bhoola > > > > > -- > Bruce Hayden > Linux on System z Advanced Technical Support > Endicott, NY -- Kris Buelens, IBM Belgium, VM customer support
