Look at Sanguino schematic, maybe helps: http://sanguino.cc/hardware
On Aug 13, 10:47 pm, Sebastien Lelong <[email protected]> wrote: > Hi Albert, > > Thanks for your suggestion, but Tiny software requires to reset via RTS, not > CTS. > Anyway, do you have a link with a schematic for what you describe ? (just to > make sure I understand clearly what you say) > > Cheers, > Seb > -- > Sébastien Lelonghttp://www.sirloon.nethttp://sirbot.org > > 2009/8/13 a.faber <[email protected]> > > > > > Hi Seb, > > Mostly I used a simple but effective reset circuit, just connect the CTS > > line with a 10uF capacitor with the reset line (and using a diode + 10K > > resistor to pull up the reset line). The cap only initiates a pulse when > > the > > CTS line is changed from high to low, the reset line will be pulled high > > after a couple of milliseconds even when the CTS line stays low. > > Albert > > > ----- Original Message ----- > > From: "Sebastien Lelong" <[email protected]> > > To: <[email protected]> > > Sent: Thursday, August 13, 2009 9:00 PM > > Subject: [jallib] Re: jaluino (resetting via RTS) > > > I tried to prototype the "reset using RTS" thing on a breadboard, but I got > > troubles (as expected...). I followed the schematic and connected D2, R2, > > R3 > > and Q1 onto the breadboard. > > > It's as though it's acting the reverse: when I plug the serial module, it > > keeps resetting the PIC. > > > When I plug the serial module: > > - Vrts ~ 4.1V (5V without hardware D2, R2, ...) > > - PIC doesn't blink the LED (keeps resetting) > > > For my tests, I used python serial module: > > > import serial > > ser = serial.Serial(port="/dev/ttyUSB0",baudrate=115200) > > > by default, when the serial connection is created by this command, RTS = 1, > > and Vrts ~ 0V. The PICs starts ! > > > ser.setRTS(1) -- will reset the PIC, Vrts ~ 4.1V > > ser.setRTS(0) -- will start the PIC, Vrts ~ 0V > > > So, it seems to work but on the contrary expected behavior. I would expect > > that by default the PIC starts. > > > Does it seem weird to you too ? Or did I miss something ? > > > Cheers, > > Seb > > > > > > Also ask by Seb is the reset option by RTS (J7). > > > > > OK this is where I'm lost... I have few questions about this: > > > > > - RTS and CTS in serial connector are connected to RD5 and RD4. Why ? > > > > If you want handshake you can use RD5 and RD4, if you dont need > > > handshake you > > > Can use RD4 and RD5 on connected I/O4 > > > > > - when I want to reset the board using RTS, I need to switch RTS J7 > > > > trigger to position 1-2, as in the schematic. Is that right ? > > > > Yes, if you put it in position 2-3 you cant use reset but you can use > > > handshake. > > > If I did not use the switch (is jumper) than you could not use RD4 as > > > normal I/O > > > because PIC would reset as soon as RD4 becomes high. > > > > > - All the serial modules I've used or built have their RTS connected > > > > to > > > > CTS. No flow control, quite common I think. Like in this article: > > >http://www.lynxmotion.com/images/html/build125.htm. Now imagine I use > > such > > > > a module with RTS and CTS connected. I plug it to the board. Will this > > > work > > > > ? Or should RTS and CTS remain unconnected from each other ? In that > > > case, > > > > do I have to deal with flow control ? (hope not...) > > > > Yes this will work and No you dont need flow control, but like in > > > your link dont connect the RTS end CTS from the serial module to the > > > serial connector of the Main Board else you cant use RD4 and RD5 for > > > other purpose. --~--~---------~--~----~------------~-------~--~----~ You received this message because you are subscribed to the Google Groups "jallib" group. To post to this group, send email to [email protected] To unsubscribe from this group, send email to [email protected] For more options, visit this group at http://groups.google.com/group/jallib?hl=en -~----------~----~----~----~------~----~------~--~---
