Sorry, but not work image captured. I think the overlay not work. On May 10, 12:52 am, Florin Tanasa <[email protected]> wrote: > Hi Vasi, > I not found 2x10, 2x4 and 2x8 connectors for cable, but I found 1x20 and 1x8 > connectors (I think the name is molex). > Some image for now situation. > > On Monday 10 May 2010 00:34:20 funlw65 wrote: > > > > > Hi, > > > Florin have a Jaluino board but would be nice to have this kind of > > shield also for Arduino boards (maybe he can fit an arduino shield > > connector - but this will increase the complexity of his shield and > > can be less practical for Jaluino board). > > > It is hard to build development boards with a maximum level of > > configurability. Always compromises are made imposed by the size of > > the board and costs. Of course is not Florin's case (and Jaluino) > > because is about a shield which can be removed. > > > I like this kind of board for his great level of configurability. Is > > not good as an application board but is great as a development board > > where all connections can be made with "Du-Pont" wires (if this is the > > right term). > > > Is for ATmega16/32 microcontrollers but It can be made also for > > PIC's. > > User Guide manual: > >http://www.adelaida.ro/adelaida/catalog/pub/TME/EVB4.3Users_manual.pdf > > > Vasi > > > On May 9, 1:49 pm, Joep Suijs <[email protected]> wrote: > > > Hi Florin, > > > > Looks very nice, the perferct evaluation board for developers ;) > > > > Some point to concider for even more improvement: > > > - What would be nice is a led or two, but there are four in a combined > > > way and you may run out of pins... > > > - And if you make e.g. jumper 1 to 4 a dip-switch, you can use it as a > > > on/off switch. > > > - And last but not least: it would be nice to have a pushbutton or > > > two, they are more easy to read than a keyboard. With a resistor from > > > 5V to the colums lines will do. > > > - And about those column lines: is there a reason they are on the > > > higher half of port D and not the lower half? The latter can be freed > > > with a character display if you use 4 bit mode... > > > > What is the use of the ne555? > > > > What will be the size of this shield? And would it be usable on an > > > arduino board? > > > > Joep > > > > 2010/5/9 Florin Tanasa <[email protected]>: > > > > Hi guys > > > > I try to make a shield for jaluino with: > > > > GLCD, LCD, Keypad, PWM, analog input, etc. > > > > This shield will be used mainly to develop a controller / logger for > > > > alternative energy systems (wind and solar) and other projects. > > > > My request is to look and say what you think about the scheme. > > > > Kind regards, > > > > -- > > > > Florin Tanasa > > > >http://sites.google.com/site/florintanasa/ > > > > > -- > > > > You received this message because you are subscribed to the Google > > > > Groups "jallib" group. To post to this group, send email to > > > > [email protected]. > > > > To unsubscribe from this group, send email to > > > > [email protected]. For more options, visit this group > > > > athttp://groups.google.com/group/jallib?hl=en. > > > > -- > > > You received this message because you are subscribed to the Google Groups > > > "jallib" group. To post to this group, send email to > > > [email protected]. > > > To unsubscribe from this group, send email to > > > [email protected]. For more options, visit this group > > > athttp://groups.google.com/group/jallib?hl=en. > > -- > Florin Tanasahttp://sites.google.com/site/florintanasa/ > > -- > You received this message because you are subscribed to the Google Groups > "jallib" group. > To post to this group, send email to [email protected]. > To unsubscribe from this group, send email to > [email protected]. > For more options, visit this group > athttp://groups.google.com/group/jallib?hl=en. > > shields_kicad_jaluino_1.jpg > 18KViewDownload > > shields_kicad_jaluino_2.jpg > 18KViewDownload
-- You received this message because you are subscribed to the Google Groups "jallib" group. To post to this group, send email to [email protected]. To unsubscribe from this group, send email to [email protected]. For more options, visit this group at http://groups.google.com/group/jallib?hl=en.
