If you are using RFC 1918 private addresses, then you will want to remove them from the Junos martian dropping.
Like: set routing-options martians 192.168.0.0/16 exact allow Info: https://www.juniper.net/documentation/en_US/junos/topics/topic-map/recognize-martian-addr-routing.html -- ______________________ David Miller dmil...@tiggee.com On Fri, Oct 9, 2020 at 11:08 AM Eric Krichbaum <e...@telic.us> wrote: > > One of many working 204s with 1G. > > Model: mx204 > Junos: 18.2R3-S1.7 > > Chassis: > PIC 1 BUILTIN BUILTIN 8XSFPP PIC > Xcvr 0 @(+ NON-JNPR F179CO14506 SFP-LX10 > Xcvr 1 NON-JNPR F179CO14505 SFP-LX10 > Xcvr 2 Et NON-JNPR G1908908498 SFP-LX10 > > Chassis ports are set 10G: > set chassis fpc 0 pic 0 tunnel-services bandwidth 200g > set chassis fpc 0 pic 0 port 0 speed 100g > set chassis fpc 0 pic 0 port 1 speed 40g > set chassis fpc 0 pic 0 port 2 speed 40g > set chassis fpc 0 pic 1 port 0 speed 10g > set chassis fpc 0 pic 1 port 1 speed 10g > set chassis fpc 0 pic 1 port 2 speed 10g > set chassis fpc 0 pic 1 port 3 speed 10g > set chassis fpc 0 pic 1 port 4 speed 10g > set chassis fpc 0 pic 1 port 5 speed 10g > set chassis fpc 0 pic 1 port 6 speed 10g > set chassis fpc 0 pic 1 port 7 speed 10g > > Interface: > set interfaces xe-0/1/0 gigether-options no-auto-negotiation > set interfaces xe-0/1/0 gigether-options speed 1g > set interfaces xe-0/1/0 unit 0 family inet rpf-check mode loose > set interfaces xe-0/1/0 unit 0 family inet address x.x.x.x/30 > set interfaces xe-0/1/0 unit 0 family inet6 address x:x:x:x::x/127 > set interfaces xe-0/1/1 gigether-options no-auto-negotiation > set interfaces xe-0/1/1 gigether-options speed 1g > set interfaces xe-0/1/1 unit 0 family inet rpf-check mode loose > set interfaces xe-0/1/1 unit 0 family inet address x.x.x.x/29 > set interfaces xe-0/1/1 unit 0 family inet6 address x:x:x:x::x:x/112 > > > Eric > > > > -----Original Message----- > From: juniper-nsp <juniper-nsp-boun...@puck.nether.net> On Behalf Of Lukasz > Trabinski > Sent: Friday, October 09, 2020 9:49 AM > To: Juniper List <juniper-nsp@puck.nether.net> > Subject: Re: [j-nsp] MX204 port 1G > > > When I removed "speed 10g" from chassis section > > > admin@mx1> show configuration |compare rollback 1 [edit chassis fpc 0 pic 1] > - port 4 { > - speed 10g; > - } > > and bounced FPC 0, interface not found. > > admin@mx1> show interfaces xe-0/1/4 > error: device xe-0/1/4 not found > > In documentation we can read that 10g is default. It’s seems not. > When I removed "speed 1G” from gigether-options section, interface is found, > but is DOWN. > > Any Idea? :) > > > > > > > Wiadomość napisana przez Richard McGovern <rmcgov...@juniper.net> w dniu > > 09.10.2020, o godz. 16:05: > > > > Correct. Unlike EX/QFX where for 1/10 capable interfaces the name will > > match the insert Optic. 1G Optic shows as ge, 10G Optic shows as xe. Both > > ge/xe names allowed. > > > > For MX/SRX (and I assume PTX and maybe ACX - don't much deal with those > > products ) xe is ONLY name allowed, and is used to indicate the interface > > is 10G capable. For show interface info, the interface will show the > > correct speed. > > > > NOTE: Please don't ask me the why. Tried to fight that battle, this will > > NOT be changed. > > > > As for William original question why are you hard coding 1G in the config, > > and setting 10G in the HW (chassis stanza)? From initial look, that is > > first place to look. BTW, on MX204, neither should needed. FPC does not > > need speed setting (default supports 1/10) and auto should work fine at > > interface config. If you needed fixed speed for working with remote device, > > then set speed at interface level only. If you are going to do both, make > > them equal, although I am guess chassis fpc only has 10G as option. > > > > Did you have issue with auto for interface, which is default setting? > > > > HTH, Rich > > > > Richard McGovern > > Sr Sales Engineer, Juniper Networks > > 978-618-3342 > > > > I’d rather be lucky than good, as I know I am not good I don’t make > > the news, I just report it > > > > > > On 10/9/20, 8:02 AM, "Łukasz Trąbiński" <luk...@trabinski.net> wrote: > > > > Hi. > > > > It does not work. according to the documentation it must be xe- > > > >> Wiadomość napisana przez Jackson, William <william.jack...@gibtele.com> w > >> dniu 09.10.2020, o godz. 13:42: > >> > >> Rename the interface ge-0/1/4 > >> > >> admin@mx1> show interfaces xe-0/1/4 > >> Physical interface: xe-0/1/4, Enabled, Physical link is Up > >> Interface index: 154, SNMP ifIndex: 530 > >> Description: TEST > >> Link-level type: Ethernet, MTU: 1514, MRU: 1522, LAN-PHY mode, > >> Speed: 10Gbps, > >> > >> On 09/10/2020, 13:16, "juniper-nsp on behalf of Łukasz Trąbiński" > >> <juniper-nsp-boun...@puck.nether.net on behalf of luk...@trabinski.net> > >> wrote: > >> > >> Hello > >> > >> In Lab I'm trying to set up 1G port on MX204. > >> > >> admin@mx1> show configuration interfaces xe-0/1/4 > >> description TEST; > >> gigether-options { > >> speed 1g; > >> } > >> unit 0 { > >> family inet { > >> address 192.168.1.138/30; > >> } > >> } > >> > >> admin@mx1> show configuration chassis fpc 0 pic 1 port 4 > >> speed 10g; > >> > >> Port is UP, but I can’t see any MAC address from remote side or I can’t > >> ping remote side. > >> > >> > >> admin@mx1> show interfaces xe-0/1/4 > >> Physical interface: xe-0/1/4, Enabled, Physical link is Up > >> Interface index: 154, SNMP ifIndex: 530 > >> Description: TEST > >> Link-level type: Ethernet, MTU: 1514, MRU: 1522, LAN-PHY mode, Speed: > >> 10Gbps, > >> BPDU Error: None, Loop Detect PDU Error: None, MAC-REWRITE Error: None, > >> Loopback: None, Source filtering: Disabled, Flow control: Enabled, > >> Speed Configuration: 1G > >> > >> > >> Junos: 18.4R3-S5.4 but also tried on 18.4R3.3. I also setup > >> auto-negotiation and fec options but without success. > >> > >> SFP: > >> Xcvr 4 REV 01 740-011614 PJD2XXX SFP-LX10 > >> _______________________________________________ > >> juniper-nsp mailing list juniper-nsp@puck.nether.net > >> > >> https://urldefense.com/v3/__https://puck.nether.net/mailman/listinfo/ > >> juniper-nsp__;!!NEt6yMaO-gk!T3KOFxazJ51vM0Q41a56Y1mr9YYi0Ruejmyy-NbGR > >> h0FKlipj4DlsqFCEEmmURbUIQ$ > >> > >> > > > > > > > > > > Juniper Business Use Only > > _______________________________________________ > juniper-nsp mailing list juniper-nsp@puck.nether.net > https://puck.nether.net/mailman/listinfo/juniper-nsp > > > -- > This email has been checked for viruses by Avast antivirus software. > https://www.avast.com/antivirus > > _______________________________________________ > juniper-nsp mailing list juniper-nsp@puck.nether.net > https://puck.nether.net/mailman/listinfo/juniper-nsp _______________________________________________ juniper-nsp mailing list juniper-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp
