Hello Bill If I understand it correctly, this machine is still on the drawing board. So suggestiions may help get this machine working like what we/people want from it. I like those idea's Bill. but lets see the finnal machine before we start changing it. ;-) I wish Legacy was not so firm on the 36" L. I think it should be shorter or longer. for what I do 36" just isnt enough. and for the wood turner that is makeing bottle stops and pens... I think it will be to big and expencive to fit the job/cost. but that is just my 2 cents worth.
Have a great day. C.A.G. ----- Original Message ----- From: Bill Bulkeley <bulke...@mmnet.com.au> To: legacy-ornamental-mills@googlegroups.com Sent: Wed, 27 Jun 2012 07:51:50 -0400 (EDT) Subject: Re: A sneak peak at the new Legacy Manual Machine curt for horizontal work it would be easy enough to make a angle bracket to bolt where the router clamp is then bolt the router clamp to the angle bracket and the router would be horizontal for bowls and such possibly no need for a rotary table then and I'm sure you could mount a template under the cross slide some were to do bowl profiles vertical template following is a must this template turning from the side we have to do sucks. perhaps spread the inner rails apart and lengthen the z axis too so the router can fit between and you could do larger rotary table stuff under the mill as well Bill ----- Original Message ----- From:curt george To:legacy-ornamental-mills@googlegroups.com Sent: Wednesday, June 27, 2012 5:54 PM Subject: Re: A sneak peak at the new Legacy Manual Machine ;-) Very true Bill. C.A.G. ----- Original Message ----- From:Bill Bulkeley To:legacy-ornamental-mills@googlegroups.com Sent: Wednesday, June 27, 2012 2:01 AM Subject: Re: A sneak peak at the new Legacy Manual Machine dont worry too much curt what ever it wont do we will make it do like we did with the old machines :) Bill ----- Original Message ----- From:curt george To:legacy-ornamental-mills@googlegroups.com Sent: Wednesday, June 27, 2012 10:12 AM Subject: Re: A sneak peak at the new Legacy Manual Machine Hello again. (3x the charm.) ;-) Ok here is my input. make this unit have a carriage that can tilt 90 deg. so you can cut bowls end grain. (turning bowls are a big market for most turners.) give it a motor drive.and make a gear for finer movement. Make the Z axis so that it can free float on a template. or better yet Give it two templates followers, one for the Y&X axis movements and one for the Z axis.(rise and plunge movements.) this might help with the pen turners market. That's all that I can think of at this moment. But If something comes up, then I will let my know. Have a good night. C.A.G. No virus found in this message. Checked by AVG - www.avg.com Version: 2012.0.2180 / Virus Database: 2437/5095 - Release Date: 06/26/12 -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. For more options, visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. For more options, visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en. No virus found in this message. Checked by AVG - www.avg.com Version: 2012.0.2180 / Virus Database: 2437/5095 - Release Date: 06/26/12 -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. For more options, visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. For more options, visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en. -- You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group. To post to this group, send email to legacy-ornamental-mills@googlegroups.com. To unsubscribe from this group, send email to legacy-ornamental-mills+unsubscr...@googlegroups.com. For more options, visit this group at http://groups.google.com/group/legacy-ornamental-mills?hl=en.