VDR works only with FF cards or budget cards (like yours) + additional hardware decoder (like Creative DXR3).
ABBAS AL-MUTAWA wrote:
Hi first Thanks for replying me fastly.
in fact, i try everythings just to get this card working, after i insmod the "dst" and fail to get the VDR or xawtv to work with, i tried to insmod the "CX24110" to see if it works, but nothings happen, the i tried remove the "dst" and insmod it again with "DST_TYPE_FLAGS=0", "DST_TYPE_FLAGS=1","DST_TYPE_FLAGS=4", but again nothings happen and the VDR cannot crab the /dev/video0 devices.
now, i am trying again form the begining, so please follow my steps and correct me if i am wrong
1) "lsmod" gives ****************************** [EMAIL PROTECTED] abbas]$ lsmod Module Size Used by autofs 17152 0 parport_pc 36492 2
2) i did the following step ******************************* [EMAIL PROTECTED] abbas]# modprobe bttv card=0x68 i2c_hw=1 [EMAIL PROTECTED] abbas]# lsmod Module Size Used by bttv 136096 0 video_buf 22272 1 bttv i2c_algo_bit 10504 1 bttv btcx_risc 4996 1 bttv i2c_core 25348 2 bttv,i2c_algo_bit autofs 17152 0 parport_pc 36492 2
3) modprobe dvb-bt8xx ************************** [EMAIL PROTECTED] abbas]# modprobe dvb-bt8xx [EMAIL PROTECTED] abbas]# lsmod Module Size Used by dvb_bt8xx 8064 0 dvb_core 60544 1 dvb_bt8xx bt878 11696 1 dvb_bt8xx bttv 136096 2 dvb_bt8xx,bt878 video_buf 22272 1 bttv i2c_algo_bit 10504 1 bttv btcx_risc 4996 1 bttv i2c_core 25348 3 dvb_bt8xx,bttv,i2c_algo_bit autofs 17152 0 parport_pc 36492 2
4)modprobe dst ****************************** [EMAIL PROTECTED] abbas]# lsmod Module Size Used by dst 14464 0 dvb_bt8xx 8064 0 dvb_core 60544 2 dst,dvb_bt8xx bt878 11696 2 dst,dvb_bt8xx bttv 136096 2 dvb_bt8xx,bt878 video_buf 22272 1 bttv i2c_algo_bit 10504 1 bttv btcx_risc 4996 1 bttv i2c_core 25348 3 dvb_bt8xx,bttv,i2c_algo_bit autofs 17152 0 parport_pc 36492 2
5) dmesg "part of it" ************************* I2O configuration manager v 0.04. (C) Copyright 1999 Red Hat Software es1371: version v0.32 time 20:01:39 Dec 20 2003 PCI: Found IRQ 3 for device 0000:02:0a.0 es1371: found chip, vendor id 0x1274 device id 0x5880 revision 0x02 es1371: found es1371 rev 2 at io 0xdf00 irq 3 joystick 0x0 ac97_codec: AC97 Audio codec, id: 0x8384:0x7609 (SigmaTel STAC9721/23) btaudio: driver version 0.7 loaded [digital+analog] PCI: Found IRQ 11 for device 0000:02:0d.1 PCI: Sharing IRQ 11 with 0000:02:0d.0 btaudio: Bt878 (rev 17) at 02:0d.1, irq: 11, latency: 32, mmio: 0xf47ff000 btaudio: using card config "default" btaudio: registered device dsp2 [digital] btaudio: registered device dsp3 [analog] btaudio: registered device mixer1 Advanced Linux Sound Architecture Driver Version 0.9.7 (Thu Sep 25 19:16:36 2003 UTC). request_module: failed /sbin/modprobe -- snd-card-0. error = -16 unable to register OSS PCM device 0:0 unable to register OSS mixer device 0:0 unable to register OSS mixer device 1:0 ALSA device list: #0: Dummy 1 #1: Virtual MIDI Card 1 NET: Registered protocol family 2 IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 65536) NET: Registered protocol family 1 NET: Registered protocol family 17 IrCOMM protocol (Dag Brattli) EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. hub 1-0:1.0: new USB device on port 1, assigned address 2 kjournald starting. Commit interval 5 seconds EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 188k freed input: USB HID v1.00 Mouse [Cypress Sem Cypress USB Mouse] on usb-0000:00:1f.2-1 hub 1-0:1.0: new USB device on port 2, assigned address 3 drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x03F0 pid 0x7004 EXT3 FS on hda9, internal journal Adding 232900k swap on /dev/hda7. Priority:-1 extents:1 cdrom: open failed. kjournald starting. Commit interval 5 seconds EXT3 FS on hda5, internal journal EXT3-fs: mounted filesystem with ordered data mode. kudzu: numerical sysctl 1 23 is obsolete. parport0: PC-style at 0x378 [PCSPP,TRISTATE,EPP] parport0: cpp_daisy: aa5500ff(38) parport0: assign_addrs: aa5500ff(38) parport0: cpp_daisy: aa5500ff(38) parport0: assign_addrs: aa5500ff(38) plip: parport0 has no IRQ. Using IRQ-less mode,which is fairly inefficient! NET3 PLIP version 2.4-parport [EMAIL PROTECTED] plip0: Parallel port at 0x378, not using IRQ. lp0: using parport0 (polling). eth0: Setting full-duplex based on MII #1 link partner capability of 45e1. spurious 8259A interrupt: IRQ7. bttv: driver version 0.9.12 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture bttv: Bt8xx card found (0). PCI: Found IRQ 11 for device 0000:02:0d.0 PCI: Sharing IRQ 11 with 0000:02:0d.1 bttv0: Bt878 (rev 17) at 0000:02:0d.0, irq: 11, latency: 32, mmio: 0xf47fe000 bttv0: using: Nebula Electronics DigiTV [card=104,insmod option] bttv0: using tuner=-1 bt878: AUDIO driver version 0.0.0 loaded dvb_bt8xx: unable to determine DMA core of card 0 attach: checking "bt878 #0 [hw]" find by pci: checking "bt878 #0 [hw]"
5) trying to run "vdr" *********************** [EMAIL PROTECTED] abbas]# vdr vdr: no primary device found - using first device!
6) running xawtv ********************** [EMAIL PROTECTED] abbas]# xawtv This is xawtv-3.90, running on Linux/i686 (2.6.0-test11) can't open /dev/video0: No such device v4l-conf had some trouble, trying to continue anyway v4l2: open /dev/video0: No such device v4l2: open /dev/video0: No such device v4l: open /dev/video0: No such device no video grabber device available
&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&& Please correct me if there is any wrong in the previous steps. tell me if there is any chance to get this card working under Linux
Thanks & best regards
abbas almutawa
--- Manu Abraham <[EMAIL PROTECTED]> wrote:
Hi,
The card is a Pinnacle card or is the CX24110
module loaded as it is by some script ?
Maybe the modules are confused looking for a
Pinnacle PC TV@ SAT card(CX24110 chipset) ? The removal of the module and loading the
modules proper with the DST_TYPE_FLAGS would help ?
Regards, Manu
On Sunday 21 December 2003 23:10, ABBAS AL-MUTAWA
wrote:
Dear Siri've
I have DVB card, "TWINHAN VP1020" built on bt878.
just correctly installed the latest DVB driver onvery
kernel-2.6.0-test11. everythings seems to work
well, I insmod the driver as wriiten in theDVB-kernel
without any errors.following
now, i have just installed DVB player which is the
VDR, but when i try to run "vdr", i get the
message.
vdr: no primary device found - using first device!
the "lsmod" command gives
__________________________________ Do you Yahoo!? New Yahoo! Photos - easier uploading and sharing. http://photos.yahoo.com/
-- Info: To unsubscribe send a mail to [EMAIL PROTECTED] with "unsubscribe linux-dvb" as subject.
