hi
> You have to create the /dev/dvbX/... entries... > There is a script in the "DVB" package at > linuxtv.org i have used makedev to create the /dev/dvb/adapter.. this is the result [EMAIL PROTECTED] driver]# sh makedev.napi Creating DVB devices in /dev/dvb/adapter0 chown: `root.video': invalid group Creating DVB devices in /dev/dvb/adapter1 chown: `root.video': invalid group Creating DVB devices in /dev/dvb/adapter2 chown: `root.video': invalid group Creating DVB devices in /dev/dvb/adapter3 chown: `root.video': invalid group now i have /dev/dvb/adapter0/... modules, but using applications to test them result in [EMAIL PROTECTED] test]# ./set22k on set22k: using '/dev/dvb/adapter0/frontend0' open: No such device [EMAIL PROTECTED] test]# ./sendburst a set22k: using '/dev/dvb/adapter0/frontend0' open: No such device [EMAIL PROTECTED] test]# ./test_dvr video 0x2000 using '/dev/dvb/adapter0/demux0' and '/dev/dvb/adapter0/dvr0' writing to 'video' cannot open dvr device: No such device [EMAIL PROTECTED] test]# ./diseqc diseqc test: using '/dev/dvb/adapter0/frontend0' open: No such device i tried to cat all these devices and the result is as shown [EMAIL PROTECTED] test]# cd /dev/dvb/adapter0/ [EMAIL PROTECTED] adapter0]# ls audio0 ca0 demux0 dvr0 frontend0 net0 osd0 video0 [EMAIL PROTECTED] adapter0]# cat audio0 cat: audio0: No such device [EMAIL PROTECTED] adapter0]# cat ca0 cat: ca0: No such device [EMAIL PROTECTED] adapter0]# cat demux0 cat: demux0: No such device [EMAIL PROTECTED] adapter0]# cat dvr0 cat: dvr0: No such device [EMAIL PROTECTED] adapter0]# cat osd0 cat: osd0: No such device [EMAIL PROTECTED] adapter0]# cat video0 cat: video0: No such device [EMAIL PROTECTED] adapter0]# i also check adapter1, adapter2, adapter3 but all of them give the same result > The driver works perfectly ... I personally use the > 2 different Twinhan cards i will not stop until get this bad card working under linux, part of /dmesg >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> btaudio: driver version 0.7 loaded [digital+analog] PCI: Found IRQ 11 for device 0000:02:0d.1 PCI: Sharing IRQ 11 with 0000:02:0d.0 btaudio: Bt878 (rev 17) at 02:0d.1, irq: 11, latency: 32, mmio: 0xf47ff000 btaudio: using card config "default" btaudio: registered device dsp2 [digital] btaudio: registered device dsp3 [analog] btaudio: registered device mixer1 Advanced Linux Sound Architecture Driver Version 0.9.7 (Thu Sep 25 19:16:36 2003 UTC). request_module: failed /sbin/modprobe -- snd-card-0. error = -16 unable to register OSS PCM device 0:0 unable to register OSS mixer device 0:0 unable to register OSS mixer device 1:0 ALSA device list: #0: Dummy 1 #1: Virtual MIDI Card 1 NET: Registered protocol family 2 IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 65536) NET: Registered protocol family 1 NET: Registered protocol family 17 IrCOMM protocol (Dag Brattli) kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 188k freed hub 1-0:1.0: new USB device on port 1, assigned address 2 input: USB HID v1.00 Mouse [Cypress Sem Cypress USB Mouse] on usb-0000:00:1f.2-1 hub 1-0:1.0: new USB device on port 2, assigned address 3 drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x03F0 pid 0x7004 EXT3 FS on hda9, internal journal Adding 232900k swap on /dev/hda7. Priority:-1 extents:1 cdrom: open failed. kjournald starting. Commit interval 5 seconds EXT3 FS on hda5, internal journal EXT3-fs: mounted filesystem with ordered data mode. kudzu: numerical sysctl 1 23 is obsolete. parport0: PC-style at 0x378 [PCSPP,TRISTATE,EPP] parport0: cpp_daisy: aa5500ff(38) parport0: assign_addrs: aa5500ff(38) parport0: cpp_daisy: aa5500ff(38) parport0: assign_addrs: aa5500ff(38) plip: parport0 has no IRQ. Using IRQ-less mode,which is fairly inefficient! NET3 PLIP version 2.4-parport [EMAIL PROTECTED] plip0: Parallel port at 0x378, not using IRQ. lp0: using parport0 (polling). kudzu: numerical sysctl 1 23 is obsolete. python2.2: numerical sysctl 1 23 is obsolete. ddcprobe: numerical sysctl 1 23 is obsolete. ddcprobe: numerical sysctl 1 23 is obsolete. python2.2: numerical sysctl 1 23 is obsolete. ddcprobe: numerical sysctl 1 23 is obsolete. python2.2: numerical sysctl 1 23 is obsolete. python2.2: numerical sysctl 1 23 is obsolete. eth0: Setting full-duplex based on MII #1 link partner capability of 45e1. spurious 8259A interrupt: IRQ7. bttv: driver version 0.9.12 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture bttv: Bt8xx card found (0). PCI: Found IRQ 11 for device 0000:02:0d.0 PCI: Sharing IRQ 11 with 0000:02:0d.1 bttv0: Bt878 (rev 17) at 0000:02:0d.0, irq: 11, latency: 32, mmio: 0xf47fe000 bttv0: using: Nebula Electronics DigiTV [card=104,insmod option] bttv0: using tuner=-1 bt878: AUDIO driver version 0.0.0 loaded dvb_bt8xx: unable to determine DMA core of card 0 attach: checking "bt878 #0 [hw]" find by pci: checking "bt878 #0 [hw]" python: numerical sysctl 1 23 is obsolete. >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> Thanks for everythings best regards abbas --- Manu Abraham <[EMAIL PROTECTED]> wrote: > On Monday 22 December 2003 21:43, ABBAS AL-MUTAWA > wrote: > > Hi > > > > after insmod the following modules successfully > > > > modprobe dvb_core dvb_shutdown_timeout=0 > > modprobe video-buf > > modprobe bttv i2c_hw=1 card=0x68 > > modprobe bt878 > > modprobe dst dst_type_flags=4 > > modprobe dvb-bt8xx > > > > i tried the test_dvr, szap,..., but all not works > > > > it is looking for /dev/dvb/video0, /dev/dvb/demx0, > > /dev/dvb/frontend0,... but all of them are not > exist > > > > You have to create the /dev/dvbX/... entries... > There is a script in the "DVB" package at > linuxtv.org > > > i have only /dev/video0, /dev/video1, /dev/video2, > > /dev/video3, /dev/video1394 > > > > but when i tried i.e "cat /dev/video0" it gives > > [EMAIL PROTECTED] dev]# cat video0 > > cat: video0: No such device > > [EMAIL PROTECTED] dev]# > > > > As i said earlier /dev/videoX would not work.. > > > > > > i dont think that the driver is working!!! > > > > The driver works perfectly ... I personally use the > 2 different Twinhan cards > ... > > > i have also. /dev/video/ which contains > > > > em8300 em8300_ma em8300_mv em8300_sp > > > > It looks like you have the DXR card and or the > kernel/module support... > That's all not the DVB card ... > > > > but cat them result > > > > [EMAIL PROTECTED] video]# cat em8300 > > cat: em8300: No such device > > [EMAIL PROTECTED] video]# cat em8300_ma > > cat: em8300_ma: No such device > > [EMAIL PROTECTED] video]# > > > > > > You do not have the DVR hardware ... Only the > kernel/module support ... > > > i also tried to open some source files like > > "test_dvr.c" and point it to /dev/video0, but > gives > > "No such device". > > > > Indeed you do not have any /dev/videoXXX > > > please, if help me as you can. > > > > I think this is all the info that's available. and > that should get you going > also, if what you have said till now is correct ... > > > > Regards, > Manu > > > __________________________________ Do you Yahoo!? New Yahoo! Photos - easier uploading and sharing. http://photos.yahoo.com/ -- Info: To unsubscribe send a mail to [EMAIL PROTECTED] with "unsubscribe linux-dvb" as subject.
