In SuSE's admin tool YaST you can choose wether the hardware clock is set
to GMT or local time. Maybe you got this wrong ?

Alternatively make sure that your /etc/rc.config contains something like
this:

--------------
#
# Set to "-u" if your system clock is set to GMT, otherwise "".
#
GMT=""

#
# Timezone (e.g. CET)
# (this will set /usr/lib/zoneinfo/localtime)
#
TIMEZONE="Israel"

-------------------

Schlomo


On Tue, 16 Oct 2001, Shaul Karl wrote:

> > Hi folks!
> >
> > 1. I reorganised my system, splitting it into multiple mount points for logistic
> > reasons. I tried using Partiton Magic, as I usually do, but on a 30Gb drive it
> > bombed out, so there was nothing for it, but to build a new minimal system,
> > install bru (my backup choice) and restore everything with overwrite i.e. what
> > came out at the other end was (after fiddling fstab and lilo.conf), a perfect
> > working system - same as before EXCEPT ... the time (IST, local time (not GMT))
> > insists on being two hours ahead of the CMOS clock. I can only correct it per
> > boot by manually using date MMDDhhmm etc. Any ideas what might be causing this &
> > how to fix? (Env = {SuSE 7.1, kernel 2.4.9, ...}) (I tried a few other nonesense
> > settings and always get the same thing. Win 2000 works OK).
> >
>
>
>
> Doesn't the fact that Win 2000 works OK means that your CMOS time is adjusted
> to show IST?
> IIRC, this can explains your time problem: Linux is adjusted to read the CMOS
> time as UTC and thus add 2 hours when it needs to show IST.
> It could be that at least with Debian, hwclock and/or some setting for the
> boot scripts can fixed that. Probably something similar for SUSE.
> BTW: hwclock can show you the CMOS actual time. IIRC it can also set the CMOS
> time. Should help you to find the cause and fix the problem.
>
>
>
> > 2. One of the "junk" systems I put together, has a P166 + 32Mb and a "dafuk" IDE
> > primary slot (The machine originally had Win 95 on a 2Gb drive which booted OK
> > from the the second IDE slot.) With Linux, I can only boot off a floppy, since
> > lilo won't allow an IDE hard disk boot from anthing other than
> > /dev/hda<something>. Upon examining the lilo.conf man page I found all sorts of
> > interesting tricks for remapping the IDE drive ID's: e.g.
> > disk=/dev/hdc bios=0x80
> > or
> > map-drive=0x82 to=0x80
> >
> > My root device is /dev/hdc5, and I boot from on /dev/fd0. I would like to use
> > the above disk= ... mapping. I modified lilo.conf to root, /dev/hda5, boot from
> > /dev/hda2 and put the boot sector on /dev/hda MBR. I also modified fstab to
> > reflect the new arrangement. Of coure lilo failed, because the new arrangements
> > are meaningless until I reboot, which I cannot do! What to do?
> >
> > Thanks to the people who supplied the "junk". I'm still looking for Pentium
> > stuff, MB with slot 7 or better.
> >
> > Regards,
> >
> >
> > Dan Feiglin
> >
> >
> > =================================================================
> > To unsubscribe, send mail to [EMAIL PROTECTED] with
> > the word "unsubscribe" in the message body, e.g., run the command
> > echo unsubscribe | mail [EMAIL PROTECTED]
> >
>
>

-- 
Schlomo Schapiro
System Administrator
MobilEye Vision Technologies Ltd.

24 Mishol Hadkalim St., Jerusalem, Israel
Telephone:  + 972-2-586-6989 Ext. 131
Mobile:     + 972-55-767898
Fax:        + 972-2-586-7720

email: [EMAIL PROTECTED]
WWW:   http://www.mobileye.com


=================================================================
To unsubscribe, send mail to [EMAIL PROTECTED] with
the word "unsubscribe" in the message body, e.g., run the command
echo unsubscribe | mail [EMAIL PROTECTED]

Reply via email to