Georg Acher wrote:
> From the logs, it look like you are using isochronous transfers and bulk
> messages for communication, is this right? Can you give me some
> source code of your driver to show the urbs submitted?
We are using only bulk transfers. I was puzzled by the isochronous calls
on the stack. Could the stack be corrupted or the code have followed a
corrupted function pointer?
I have attached the driver, digi_acceleport.c; it fits in with Greg's
usb serial driver and an earlier version is already in the usb sources
in drivers/usb/serial. Let me know if you see any problems in the
way we are doing things there.
> BTW: Can you try an older kernel version, like 2.3.99pre1?
I will.
Thanks for looking at this.
-- Al
/*
* Digi AccelePort USB-4 Serial Converter
*
* Copyright 2000 by Digi International
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* Shamelessly based on Brian Warner's keyspan_pda.c and Greg Kroah-Hartman's
* usb-serial driver.
*
* Peter Berger ([EMAIL PROTECTED])
* Al Borchers ([EMAIL PROTECTED])
*
* (5/16/2000) pberger and borchers
* -- added timeouts to sleeps
* -- handle transition to/from B0 in digi_set_termios
*
* (5/13/2000) pberger and borchers
* -- all commands now sent on out of band port, using digi_write_oob
* -- get modem control signals whenever they change, support TIOCMGET/
* SET/BIS/BIC ioctls
* -- digi_set_termios now supports parity, word size, stop bits, and
* receive enable
* -- cleaned up open and close, use digi_set_termios and digi_write_oob
* to set port parameters
* -- added digi_startup_device to start read chains on all ports
* -- write buffer is only used when count==1, to be sure put_char can
* write a char (unless the buffer is full)
*
* (5/10/2000) pberger and borchers
* -- Added MOD_INC_USE_COUNT/MOD_DEC_USE_COUNT calls
* -- Fixed problem where the first incoming character is lost on
* port opens after the first close on that port. Now we keep
* the read_urb chain open until shutdown.
* -- Added more port conditioning calls in digi_open and digi_close.
* -- Convert port->active to a use count so that we can deal with multiple
* opens and closes properly.
* -- Fixed some problems with the locking code.
*
* (5/3/2000) pberger and borchers
* -- First alpha version of the driver--many known limitations and bugs.
*
* $Id: digi_acceleport.c,v 1.43 2000/05/17 03:21:38 root Exp root $
*/
#include <linux/config.h>
#ifdef CONFIG_USB_SERIAL_DIGI_ACCELEPORT
#include <linux/kernel.h>
#include <linux/sched.h>
#include <linux/signal.h>
#include <linux/errno.h>
#include <linux/poll.h>
#include <linux/init.h>
#include <linux/malloc.h>
#include <linux/fcntl.h>
#include <linux/tty_driver.h>
#include <linux/tty_flip.h>
#include <linux/tty.h>
#include <linux/module.h>
#include <linux/spinlock.h>
#ifdef CONFIG_USB_SERIAL_DEBUG
#define DEBUG
#else
#undef DEBUG
#endif
#include <linux/usb.h>
#include "usb-serial.h"
/* Defines */
/* port buffer length -- must be <= transfer buffer length - 2 */
/* so we can be sure to send the full buffer in one urb */
#define DIGI_PORT_BUF_LEN 16
/* retry timeout while waiting for urb->status to go to 0 */
#define DIGI_RETRY_TIMEOUT (HZ/10)
/* AccelePort USB Defines */
/* ids */
#define DIGI_VENDOR_ID 0x05c5
#define DIGI_ID 0x0004
/* commands
* "INB": can be used on the in-band endpoint
* "OOB": can be used on the out-of-band endpoint
*/
#define DIGI_CMD_SET_BAUD_RATE 0 /* INB, OOB */
#define DIGI_CMD_SET_WORD_SIZE 1 /* INB, OOB */
#define DIGI_CMD_SET_PARITY 2 /* INB, OOB */
#define DIGI_CMD_SET_STOP_BITS 3 /* INB, OOB */
#define DIGI_CMD_SET_INPUT_FLOW_CONTROL 4 /* INB, OOB */
#define DIGI_CMD_SET_OUTPUT_FLOW_CONTROL 5 /* INB, OOB */
#define DIGI_CMD_SET_DTR_SIGNAL 6 /* INB, OOB */
#define DIGI_CMD_SET_RTS_SIGNAL 7 /* INB, OOB */
#define DIGI_CMD_READ_INPUT_SIGNALS 8 /* OOB */
#define DIGI_CMD_IFLUSH_FIFO 9 /* OOB */
#define DIGI_CMD_RECEIVE_ENABLE 10 /* INB, OOB */
#define DIGI_CMD_BREAK_CONTROL 11 /* INB, OOB */
#define DIGI_CMD_LOCAL_LOOPBACK 12 /* INB, OOB */
#define DIGI_CMD_TRANSMIT_IDLE 13 /* INB, OOB */
#define DIGI_CMD_READ_UART_REGISTER 14 /* OOB */
#define DIGI_CMD_WRITE_UART_REGISTER 15 /* INB, OOB */
#define DIGI_CMD_AND_UART_REGISTER 16 /* INB, OOB */
#define DIGI_CMD_OR_UART_REGISTER 17 /* INB, OOB */
#define DIGI_CMD_SEND_DATA 18 /* INB */
#define DIGI_CMD_RECEIVE_DATA 19 /* INB */
#define DIGI_CMD_RECEIVE_DISABLE 20 /* INB */
#define DIGI_CMD_GET_PORT_TYPE 21 /* OOB */
/* baud rates */
#define DIGI_BAUD_50 0
#define DIGI_BAUD_75 1
#define DIGI_BAUD_110 2
#define DIGI_BAUD_150 3
#define DIGI_BAUD_200 4
#define DIGI_BAUD_300 5
#define DIGI_BAUD_600 6
#define DIGI_BAUD_1200 7
#define DIGI_BAUD_1800 8
#define DIGI_BAUD_2400 9
#define DIGI_BAUD_4800 10
#define DIGI_BAUD_7200 11
#define DIGI_BAUD_9600 12
#define DIGI_BAUD_14400 13
#define DIGI_BAUD_19200 14
#define DIGI_BAUD_28800 15
#define DIGI_BAUD_38400 16
#define DIGI_BAUD_57600 17
#define DIGI_BAUD_76800 18
#define DIGI_BAUD_115200 19
#define DIGI_BAUD_153600 20
#define DIGI_BAUD_230400 21
#define DIGI_BAUD_460800 22
/* arguments */
#define DIGI_WORD_SIZE_5 0
#define DIGI_WORD_SIZE_6 1
#define DIGI_WORD_SIZE_7 2
#define DIGI_WORD_SIZE_8 3
#define DIGI_PARITY_NONE 0
#define DIGI_PARITY_ODD 1
#define DIGI_PARITY_EVEN 2
#define DIGI_PARITY_MARK 3
#define DIGI_PARITY_SPACE 4
#define DIGI_STOP_BITS_1 0
#define DIGI_STOP_BITS_2 1
#define DIGI_INPUT_FLOW_CONTROL_XON_XOFF 1
#define DIGI_INPUT_FLOW_CONTROL_RTS 2
#define DIGI_INPUT_FLOW_CONTROL_DTR 4
#define DIGI_OUTPUT_FLOW_CONTROL_XON_XOFF 1
#define DIGI_OUTPUT_FLOW_CONTROL_CTS 2
#define DIGI_OUTPUT_FLOW_CONTROL_DSR 4
#define DIGI_DTR_INACTIVE 0
#define DIGI_DTR_ACTIVE 1
#define DIGI_DTR_INPUT_FLOW_CONTROL 2
#define DIGI_RTS_INACTIVE 0
#define DIGI_RTS_ACTIVE 1
#define DIGI_RTS_INPUT_FLOW_CONTROL 2
#define DIGI_RTS_TOGGLE 3
#define DIGI_FLUSH_TX 1
#define DIGI_FLUSH_RX 2
#define DIGI_RESUME_TX 4 /* clears xoff condition */
#define DIGI_DISABLE 0
#define DIGI_ENABLE 1
#define DIGI_DEASSERT 0
#define DIGI_ASSERT 1
/* in band status codes */
#define DIGI_OVERRUN_ERROR 4
#define DIGI_PARITY_ERROR 8
#define DIGI_FRAMING_ERROR 16
#define DIGI_BREAK_ERROR 32
/* out of band status */
#define DIGI_NO_ERROR 0
#define DIGI_BAD_FIRST_PARAMETER 1
#define DIGI_BAD_SECOND_PARAMETER 2
#define DIGI_INVALID_LINE 3
#define DIGI_INVALID_OPCODE 4
/* input signals */
#define DIGI_READ_INPUT_SIGNALS_SLOT 1
#define DIGI_READ_INPUT_SIGNALS_ERR 2
#define DIGI_READ_INPUT_SIGNALS_BUSY 4
#define DIGI_READ_INPUT_SIGNALS_PE 8
#define DIGI_READ_INPUT_SIGNALS_CTS 16
#define DIGI_READ_INPUT_SIGNALS_DSR 32
#define DIGI_READ_INPUT_SIGNALS_RI 64
#define DIGI_READ_INPUT_SIGNALS_DCD 128
/* macros */
#define MAX(a,b) (((a)>(b))?(a):(b))
#define MIN(a,b) (((a)<(b))?(a):(b))
/* Structures */
typedef struct digi_private {
spinlock_t dp_port_lock;
int dp_buf_len;
unsigned char dp_buf[DIGI_PORT_BUF_LEN];
unsigned int dp_modem_signals;
} digi_private_t;
/* Local Function Declarations */
static int digi_write_oob( unsigned char *buf, int count );
static int digi_set_modem_signals( struct usb_serial_port *port,
unsigned int modem_signals );
static void digi_rx_throttle (struct usb_serial_port *port);
static void digi_rx_unthrottle (struct usb_serial_port *port);
static void digi_set_termios( struct usb_serial_port *port,
struct termios *old_termios );
static void digi_break_ctl( struct usb_serial_port *port, int break_state );
static int digi_ioctl( struct usb_serial_port *port, struct file *file,
unsigned int cmd, unsigned long arg );
static int digi_write( struct usb_serial_port *port, int from_user,
const unsigned char *buf, int count );
static void digi_write_bulk_callback( struct urb *urb );
static int digi_write_room( struct usb_serial_port *port );
static int digi_chars_in_buffer( struct usb_serial_port *port );
static int digi_open( struct usb_serial_port *port, struct file *filp );
static void digi_close( struct usb_serial_port *port, struct file *filp );
static int digi_startup_device( struct usb_serial *serial );
static int digi_startup( struct usb_serial *serial );
static void digi_shutdown( struct usb_serial *serial );
static void digi_read_bulk_callback( struct urb *urb );
static void digi_read_oob( struct urb *urb );
/* Statics */
/* device info needed for the Digi serial converter */
static __u16 digi_vendor_id = DIGI_VENDOR_ID;
static __u16 digi_product_id = DIGI_ID;
/* out of band port */
static int oob_port_num; /* index of out-of-band port */
static struct usb_serial_port *oob_port; /* out-of-band port */
static int device_startup = 0;
/* startup lock -- used to by digi_startup_device */
spinlock_t startup_lock;
/* Globals */
struct usb_serial_device_type digi_acceleport_device = {
name: "Digi USB",
idVendor: &digi_vendor_id,
idProduct: &digi_product_id,
needs_interrupt_in: DONT_CARE,
needs_bulk_in: MUST_HAVE,
needs_bulk_out: MUST_HAVE,
num_interrupt_in: 0,
num_bulk_in: 5,
num_bulk_out: 5,
num_ports: 4,
open: digi_open,
close: digi_close,
write: digi_write,
write_room: digi_write_room,
write_bulk_callback: digi_write_bulk_callback,
read_bulk_callback: digi_read_bulk_callback,
chars_in_buffer: digi_chars_in_buffer,
throttle: digi_rx_throttle,
unthrottle: digi_rx_unthrottle,
ioctl: digi_ioctl,
set_termios: digi_set_termios,
break_ctl: digi_break_ctl,
startup: digi_startup,
shutdown: digi_shutdown,
};
/* Functions */
/*
* Digi Write OOB
*
* Write commands on the out of band port. Commands are 4
* bytes each, multiple commands can be sent at once, and
* no command will be split across USB packets. Returns 0
* if successful, -EINTR if interrupted while sleeping, or
* a negative error returned by usb_submit_urb.
*/
static int digi_write_oob( unsigned char *buf, int count )
{
int ret = 0;
int len;
digi_private_t *oob_priv = (digi_private_t *)(oob_port->private);
dbg( "digi_write_oob: TOP: port=%d, count=%d", oob_port->number, count );
spin_lock( &oob_priv->dp_port_lock );
while( count > 0 ) {
while( oob_port->write_urb->status == -EINPROGRESS ) {
spin_unlock( &oob_priv->dp_port_lock );
interruptible_sleep_on_timeout( &oob_port->write_wait,
DIGI_RETRY_TIMEOUT );
if( signal_pending(current) ) {
return( -EINTR );
}
spin_lock( &oob_priv->dp_port_lock );
}
/* len must be a multiple of 4, so commands are not split */
len = MIN( count, oob_port->bulk_out_size );
if( len > 4 )
len &= ~3;
memcpy( oob_port->write_urb->transfer_buffer, buf, len );
oob_port->write_urb->transfer_buffer_length = len;
if( (ret=usb_submit_urb(oob_port->write_urb)) == 0 ) {
count -= len;
buf += len;
} else {
dbg( "digi_write_oob: usb_submit_urb failed, ret=%d",
ret );
break;
}
}
spin_unlock( &oob_priv->dp_port_lock );
return( ret );
}
/*
* Digi Set Modem Signals
*
* Sets or clears DTR and RTS on the port, according to the
* modem_signals argument. Use TIOCM_DTR and TIOCM_RTS flags
* for the modem_signals argument. Returns 0 if successful,
* -EINTR if interrupted while sleeping, or a non-zero error
* returned by usb_submit_urb.
*/
static int digi_set_modem_signals( struct usb_serial_port *port,
unsigned int modem_signals )
{
int ret;
unsigned char *data = oob_port->write_urb->transfer_buffer;
digi_private_t *port_priv = (digi_private_t *)(port->private);
digi_private_t *oob_priv = (digi_private_t *)(oob_port->private);
dbg( "digi_set_modem_signals: TOP: port=%d, modem_signals=0x%x",
port->number, modem_signals );
spin_lock( &oob_priv->dp_port_lock );
spin_lock( &port_priv->dp_port_lock );
while( oob_port->write_urb->status == -EINPROGRESS ) {
spin_unlock( &port_priv->dp_port_lock );
spin_unlock( &oob_priv->dp_port_lock );
interruptible_sleep_on_timeout( &oob_port->write_wait,
DIGI_RETRY_TIMEOUT );
if( signal_pending(current) ) {
return( -EINTR );
}
spin_lock( &oob_priv->dp_port_lock );
spin_lock( &port_priv->dp_port_lock );
}
/* command is 4 bytes: command, line, argument, pad */
data[0] = DIGI_CMD_SET_DTR_SIGNAL;
data[1] = port->number;
data[2] = (modem_signals&TIOCM_DTR) ?
DIGI_DTR_ACTIVE : DIGI_DTR_INACTIVE;
data[3] = 0;
data[4] = DIGI_CMD_SET_RTS_SIGNAL;
data[5] = port->number;
data[6] = (modem_signals&TIOCM_RTS) ?
DIGI_RTS_ACTIVE : DIGI_RTS_INACTIVE;
data[7] = 0;
oob_port->write_urb->transfer_buffer_length = 8;
if( (ret=usb_submit_urb(oob_port->write_urb)) == 0 ) {
port_priv->dp_modem_signals =
(port_priv->dp_modem_signals&~(TIOCM_DTR|TIOCM_RTS))
| (modem_signals&(TIOCM_DTR|TIOCM_RTS));
} else {
dbg( "digi_set_modem_signals: usb_submit_urb failed, ret=%d",
ret );
}
spin_unlock( &port_priv->dp_port_lock );
spin_unlock( &oob_priv->dp_port_lock );
return( ret );
}
static void digi_rx_throttle( struct usb_serial_port *port )
{
dbg( "digi_rx_throttle: TOP: port=%d", port->number );
/* stop receiving characters. We just turn off the URB request, and
let chars pile up in the device. If we're doing hardware
flowcontrol, the device will signal the other end when its buffer
fills up. If we're doing XON/XOFF, this would be a good time to
send an XOFF, although it might make sense to foist that off
upon the device too. */
// usb_unlink_urb(port->interrupt_in_urb);
}
static void digi_rx_unthrottle( struct usb_serial_port *port )
{
dbg( "digi_rx_unthrottle: TOP: port=%d", port->number );
/* just restart the receive interrupt URB */
//if (usb_submit_urb(port->interrupt_in_urb))
// dbg( "digi_rx_unthrottle: usb_submit_urb failed" );
}
static void digi_set_termios( struct usb_serial_port *port,
struct termios *old_termios )
{
unsigned int iflag = port->tty->termios->c_iflag;
unsigned int cflag = port->tty->termios->c_cflag;
unsigned int old_iflag = old_termios->c_iflag;
unsigned int old_cflag = old_termios->c_cflag;
unsigned char buf[32];
int arg,ret;
int i = 0;
dbg( "digi_set_termios: TOP: port=%d, iflag=0x%x, old_iflag=0x%x, cflag=0x%x,
old_cflag=0x%x", port->number, iflag, old_iflag, cflag, old_cflag );
/* set baud rate */
if( (cflag&CBAUD) != (old_cflag&CBAUD) ) {
arg = -1;
/* reassert DTR and (maybe) RTS on transition from B0 */
if( (old_cflag&CBAUD) == B0 ) {
/* don't set RTS if using hardware flow control */
/* and throttling input -- not implemented yet */
digi_set_modem_signals( port, TIOCM_DTR|TIOCM_RTS );
}
switch( (cflag&CBAUD) ) {
/* drop DTR and RTS on transition to B0 */
case B0: digi_set_modem_signals( port, 0 ); break;
case B50: arg = DIGI_BAUD_50; break;
case B75: arg = DIGI_BAUD_75; break;
case B110: arg = DIGI_BAUD_110; break;
case B150: arg = DIGI_BAUD_150; break;
case B200: arg = DIGI_BAUD_200; break;
case B300: arg = DIGI_BAUD_300; break;
case B600: arg = DIGI_BAUD_600; break;
case B1200: arg = DIGI_BAUD_1200; break;
case B1800: arg = DIGI_BAUD_1800; break;
case B2400: arg = DIGI_BAUD_2400; break;
case B4800: arg = DIGI_BAUD_4800; break;
case B9600: arg = DIGI_BAUD_9600; break;
case B19200: arg = DIGI_BAUD_19200; break;
case B38400: arg = DIGI_BAUD_38400; break;
case B57600: arg = DIGI_BAUD_57600; break;
case B115200: arg = DIGI_BAUD_115200; break;
case B230400: arg = DIGI_BAUD_230400; break;
case B460800: arg = DIGI_BAUD_460800; break;
default:
dbg( "digi_set_termios: can't handle baud rate 0x%x",
(cflag&CBAUD) );
break;
}
if( arg != -1 ) {
buf[i++] = DIGI_CMD_SET_BAUD_RATE;
buf[i++] = port->number;
buf[i++] = arg;
buf[i++] = 0;
}
}
/* set parity */
if( (cflag&(PARENB|PARODD)) != (old_cflag&(PARENB|PARODD)) ) {
if( (cflag&PARENB) ) {
if( (cflag&PARODD) )
arg = DIGI_PARITY_ODD;
else
arg = DIGI_PARITY_EVEN;
} else {
arg = DIGI_PARITY_NONE;
}
buf[i++] = DIGI_CMD_SET_PARITY;
buf[i++] = port->number;
buf[i++] = arg;
buf[i++] = 0;
}
/* set word size */
if( (cflag&CSIZE) != (old_cflag&CSIZE) ) {
arg = -1;
switch( (cflag&CSIZE) ) {
case CS5: arg = DIGI_WORD_SIZE_5; break;
case CS6: arg = DIGI_WORD_SIZE_6; break;
case CS7: arg = DIGI_WORD_SIZE_7; break;
case CS8: arg = DIGI_WORD_SIZE_8; break;
default:
dbg( "digi_set_termios: can't handle word size %d",
(cflag&CSIZE) );
break;
}
if( arg != -1 ) {
buf[i++] = DIGI_CMD_SET_WORD_SIZE;
buf[i++] = port->number;
buf[i++] = arg;
buf[i++] = 0;
}
}
/* set stop bits */
if( (cflag&CSTOPB) != (old_cflag&CSTOPB) ) {
if( (cflag&CSTOPB) )
arg = DIGI_STOP_BITS_2;
else
arg = DIGI_STOP_BITS_1;
buf[i++] = DIGI_CMD_SET_STOP_BITS;
buf[i++] = port->number;
buf[i++] = arg;
buf[i++] = 0;
}
/* set input flow control */
if( (iflag&IXOFF) != (old_iflag&IXOFF)
|| (cflag&CRTSCTS) != (old_cflag&CRTSCTS) ) {
arg = 0;
if( (iflag&IXOFF) )
arg |= DIGI_INPUT_FLOW_CONTROL_XON_XOFF;
else
arg &= ~DIGI_INPUT_FLOW_CONTROL_XON_XOFF;
if( (cflag&CRTSCTS) )
arg |= DIGI_INPUT_FLOW_CONTROL_RTS;
else
arg &= ~DIGI_INPUT_FLOW_CONTROL_RTS;
buf[i++] = DIGI_CMD_SET_INPUT_FLOW_CONTROL;
buf[i++] = port->number;
buf[i++] = arg;
buf[i++] = 0;
}
/* set output flow control */
/*if( (iflag&IXON) != (old_iflag&IXON)
|| (cflag&CRTSCTS) != (old_cflag&CRTSCTS) )*/ {
arg = 0;
if( (iflag&IXON) )
arg |= DIGI_OUTPUT_FLOW_CONTROL_XON_XOFF;
else
arg &= ~DIGI_OUTPUT_FLOW_CONTROL_XON_XOFF;
if( (cflag&CRTSCTS) )
arg |= DIGI_OUTPUT_FLOW_CONTROL_CTS;
else
arg &= ~DIGI_OUTPUT_FLOW_CONTROL_CTS;
buf[i++] = DIGI_CMD_SET_OUTPUT_FLOW_CONTROL;
buf[i++] = port->number;
buf[i++] = arg;
buf[i++] = 0;
}
/* set receive enable/disable */
if( (cflag&CREAD) != (old_cflag&CREAD) ) {
if( (cflag&CREAD) )
arg = DIGI_ENABLE;
else
arg = DIGI_DISABLE;
buf[i++] = DIGI_CMD_RECEIVE_ENABLE;
buf[i++] = port->number;
buf[i++] = arg;
buf[i++] = 0;
}
if( (ret=digi_write_oob( buf, i )) != 0 )
dbg( "digi_set_termios: write oob failed, ret=%d", ret );
}
static void digi_break_ctl( struct usb_serial_port *port, int break_state )
{
dbg( "digi_break_ctl: TOP: port=%d", port->number );
}
static int digi_ioctl( struct usb_serial_port *port, struct file *file,
unsigned int cmd, unsigned long arg )
{
digi_private_t *priv = (digi_private_t *)(port->private);
unsigned int val;
dbg( "digi_ioctl: TOP: port=%d, cmd=0x%x", port->number, cmd );
switch (cmd) {
case TIOCMGET:
spin_lock( &priv->dp_port_lock );
val = priv->dp_modem_signals;
spin_unlock( &priv->dp_port_lock );
if( copy_to_user((unsigned int *)arg, &val, sizeof(int)) )
return( -EFAULT );
return( 0 );
case TIOCMSET:
case TIOCMBIS:
case TIOCMBIC:
if( copy_from_user(&val, (unsigned int *)arg, sizeof(int)) )
return( -EFAULT );
spin_lock( &priv->dp_port_lock );
if( cmd == TIOCMBIS )
val = priv->dp_modem_signals | val;
else if( cmd == TIOCMBIC )
val = priv->dp_modem_signals & ~val;
spin_unlock( &priv->dp_port_lock );
return( digi_set_modem_signals( port, val ) );
case TIOCMIWAIT:
/* wait for any of the 4 modem inputs (DCD,RI,DSR,CTS)*/
/* TODO */
return( 0 );
case TIOCGICOUNT:
/* return count of modemline transitions */
/* TODO */
return 0;
}
return( -ENOIOCTLCMD );
}
static int digi_write( struct usb_serial_port *port, int from_user,
const unsigned char *buf, int count )
{
int ret,data_len,new_len;
digi_private_t *priv = (digi_private_t *)(port->private);
dbg( "digi_write: TOP: port=%d, count=%d, from_user=%d, in_interrupt=%d",
port->number, count, from_user, in_interrupt() );
/* be sure only one write proceeds at a time */
/* there are races on the port private buffer */
/* and races to check write_urb->status */
spin_lock( &priv->dp_port_lock );
/* wait for urb status clear to submit another urb */
if( port->write_urb->status == -EINPROGRESS ) {
/* buffer data if count is 1 (probably put_char) if possible */
if( /* count == */ 1 ) {
new_len = MIN( /* count */ 1,
DIGI_PORT_BUF_LEN-priv->dp_buf_len );
memcpy( priv->dp_buf+priv->dp_buf_len, buf, new_len );
priv->dp_buf_len += new_len;
} else {
new_len = 0;
}
spin_unlock( &priv->dp_port_lock );
return( new_len );
}
/* allow space for any buffered data and for new data, up to */
/* transfer buffer size - 2 (for command and length bytes) */
new_len = MIN( count, port->bulk_out_size-2-priv->dp_buf_len );
data_len = new_len + priv->dp_buf_len;
if( data_len == 0 ) {
spin_unlock( &priv->dp_port_lock );
return( 0 );
}
*((unsigned char *)(port->write_urb->transfer_buffer))
= (unsigned char)DIGI_CMD_SEND_DATA;
*((unsigned char *)(port->write_urb->transfer_buffer)+1)
= (unsigned char)data_len;
port->write_urb->transfer_buffer_length = data_len+2;
/* copy in buffered data first */
memcpy( port->write_urb->transfer_buffer+2, priv->dp_buf,
priv->dp_buf_len );
/* copy in new data */
if( from_user ) {
copy_from_user(
port->write_urb->transfer_buffer+2+priv->dp_buf_len,
buf, new_len );
} else {
memcpy( port->write_urb->transfer_buffer+2+priv->dp_buf_len,
buf, new_len );
}
#ifdef DEBUG_DATA
{
int i;
printk( KERN_DEBUG __FILE__ ": digi_write: port=%d, length=%d, data=",
port->number, port->write_urb->transfer_buffer_length );
for( i=0; i<port->write_urb->transfer_buffer_length; ++i ) {
printk( "%.2x ",
((unsigned char *)port->write_urb->transfer_buffer)[i] );
}
printk( "\n" );
}
#endif
if( (ret=usb_submit_urb(port->write_urb)) == 0 ) {
ret = new_len;
priv->dp_buf_len = 0;
} else {
dbg( "digi_write: usb_submit_urb failed, ret=%d",
ret );
/* no bytes written - should we return the error code or 0? */
ret = 0;
}
/* return length of new data written, or error */
dbg( "digi_write: returning %d", ret );
spin_unlock( &priv->dp_port_lock );
return( ret );
}
static void digi_write_bulk_callback( struct urb *urb )
{
struct usb_serial_port *port = (struct usb_serial_port *)urb->context;
struct usb_serial *serial = port->serial;
struct tty_struct *tty = port->tty;
digi_private_t *priv = (digi_private_t *)(port->private);
int ret;
dbg( "digi_write_bulk_callback: TOP: port=%d", port->number );
/* handle callback on out-of-band port */
if( port->number == oob_port_num ) {
dbg( "digi_write_bulk_callback: oob callback" );
wake_up_interruptible( &port->write_wait );
return;
}
/* sanity checks */
if( port_paranoia_check( port, "digi_write_bulk_callback" )
|| serial_paranoia_check( serial, "digi_write_bulk_callback" ) ) {
return;
}
/* try to send any buffered data on this port */
spin_lock( &priv->dp_port_lock );
if( port->write_urb->status != -EINPROGRESS && priv->dp_buf_len > 0 ) {
*((unsigned char *)(port->write_urb->transfer_buffer))
= (unsigned char)DIGI_CMD_SEND_DATA;
*((unsigned char *)(port->write_urb->transfer_buffer)+1)
= (unsigned char)priv->dp_buf_len;
port->write_urb->transfer_buffer_length = priv->dp_buf_len+2;
memcpy( port->write_urb->transfer_buffer+2, priv->dp_buf,
priv->dp_buf_len );
#ifdef DEBUG_DATA
{
int i;
printk( KERN_DEBUG __FILE__ ": digi_write_bulk_callback: port=%d, length=%d,
data=",
port->number, port->write_urb->transfer_buffer_length );
for( i=0; i<port->write_urb->transfer_buffer_length; ++i ) {
printk( "%.2x ",
((unsigned char *)port->write_urb->transfer_buffer)[i] );
}
printk( "\n" );
}
#endif
if( (ret=usb_submit_urb(port->write_urb)) == 0 ) {
priv->dp_buf_len = 0;
} else {
dbg( "digi_write_bulk_callback: usb_submit_urb failed,
ret=%d", ret );
}
}
spin_unlock( &priv->dp_port_lock );
/* wake up port processes */
wake_up_interruptible( &port->write_wait );
/* wake up line discipline */
tty = port->tty;
if( (tty->flags & (1 << TTY_DO_WRITE_WAKEUP))
&& tty->ldisc.write_wakeup )
(tty->ldisc.write_wakeup)(tty);
/* wake up other tty processes */
wake_up_interruptible( &tty->write_wait );
}
static int digi_write_room( struct usb_serial_port *port )
{
int room;
digi_private_t *priv = (digi_private_t *)(port->private);
dbg( "digi_write_room: TOP: port=%d", port->number );
spin_lock( &priv->dp_port_lock );
if( port->write_urb->status == -EINPROGRESS )
room = 0;
else
room = port->bulk_out_size - 2 - priv->dp_buf_len;
spin_unlock( &priv->dp_port_lock );
dbg( "digi_write_room: port=%d, room=%d", port->number, room );
return( room );
}
static int digi_chars_in_buffer( struct usb_serial_port *port )
{
digi_private_t *priv = (digi_private_t *)(port->private);
dbg( "digi_chars_in_buffer: TOP: port=%d", port->number );
if( port->write_urb->status == -EINPROGRESS ) {
dbg( "digi_chars_in_buffer: port=%d, chars=%d", port->number, port->bulk_out_size - 2
);
return( port->bulk_out_size - 2 );
} else {
dbg( "digi_chars_in_buffer: port=%d, chars=%d", port->number, priv->dp_buf_len );
return( priv->dp_buf_len );
}
}
static int digi_open( struct usb_serial_port *port, struct file *filp )
{
int i = 0;
int ret;
unsigned char buf[32];
digi_private_t *priv = (digi_private_t *)(port->private);
struct termios not_termios;
dbg( "digi_open: TOP: port %d, active:%d", port->number, port->active );
/* be sure the device is started up */
if( digi_startup_device( port->serial ) != 0 )
return( -ENXIO );
MOD_INC_USE_COUNT;
/* if port is already open, just return */
/* be sure exactly one open proceeds */
spin_lock( &priv->dp_port_lock );
if( port->active++ ) {
spin_unlock( &priv->dp_port_lock );
return( 0 );
}
spin_unlock( &priv->dp_port_lock );
/* read modem signals automatically whenever they change */
buf[i++] = DIGI_CMD_READ_INPUT_SIGNALS;
buf[i++] = port->number;
buf[i++] = DIGI_ENABLE;
buf[i++] = 0;
/* flush fifos */
buf[i++] = DIGI_CMD_IFLUSH_FIFO;
buf[i++] = port->number;
buf[i++] = DIGI_FLUSH_TX | DIGI_FLUSH_RX;
buf[i++] = 0;
if( (ret=digi_write_oob( buf, i )) != 0 )
dbg( "digi_open: write oob failed, ret=%d", ret );
/* set termios settings */
not_termios.c_cflag = ~port->tty->termios->c_cflag;
not_termios.c_iflag = ~port->tty->termios->c_iflag;
digi_set_termios( port, ¬_termios );
/* set DTR and RTS */
digi_set_modem_signals( port, TIOCM_DTR|TIOCM_RTS );
return( 0 );
}
static void digi_close( struct usb_serial_port *port, struct file *filp )
{
int i = 0;
int ret;
unsigned char buf[32];
digi_private_t *priv = (digi_private_t *)(port->private);
dbg( "digi_close: TOP: port %d, active:%d", port->number, port->active );
/* do cleanup only after final close on this port */
spin_lock( &priv->dp_port_lock );
if( --port->active ) {
spin_unlock( &priv->dp_port_lock );
MOD_DEC_USE_COUNT;
return;
}
spin_unlock( &priv->dp_port_lock );
/* drop DTR and RTS */
digi_set_modem_signals( port, 0 );
/* disable input flow control */
buf[i++] = DIGI_CMD_SET_INPUT_FLOW_CONTROL;
buf[i++] = port->number;
buf[i++] = DIGI_DISABLE;
buf[i++] = 0;
/* disable output flow control */
buf[i++] = DIGI_CMD_SET_OUTPUT_FLOW_CONTROL;
buf[i++] = port->number;
buf[i++] = DIGI_DISABLE;
buf[i++] = 0;
/* disable reading modem signals automatically */
buf[i++] = DIGI_CMD_READ_INPUT_SIGNALS;
buf[i++] = port->number;
buf[i++] = DIGI_DISABLE;
buf[i++] = 0;
/* flush fifos */
buf[i++] = DIGI_CMD_IFLUSH_FIFO;
buf[i++] = port->number;
buf[i++] = DIGI_FLUSH_TX | DIGI_FLUSH_RX;
buf[i++] = 0;
/* disable receive */
buf[i++] = DIGI_CMD_RECEIVE_ENABLE;
buf[i++] = port->number;
buf[i++] = DIGI_DISABLE;
buf[i++] = 0;
if( (ret=digi_write_oob( buf, i )) != 0 )
dbg( "digi_close: write oob failed, ret=%d", ret );
/* wait for final commands on oob port to complete */
while( oob_port->write_urb->status == -EINPROGRESS ) {
interruptible_sleep_on_timeout( &oob_port->write_wait,
DIGI_RETRY_TIMEOUT );
if( signal_pending(current) ) {
break;
}
}
/* shutdown any outstanding bulk writes */
usb_unlink_urb (port->write_urb);
MOD_DEC_USE_COUNT;
}
/*
* Digi Startup Device
*
* Starts reads on all ports. Must be called AFTER startup, with
* urbs initialized. Returns 0 if successful, non-zero error otherwise.
*/
static int digi_startup_device( struct usb_serial *serial )
{
int i,ret = 0;
spin_lock( &startup_lock );
/* be sure this happens exactly once */
if( device_startup ) {
spin_unlock( &startup_lock );
return( 0 );
}
/* start reading from each bulk in endpoint for the device */
for( i=0; i<digi_acceleport_device.num_ports+1; i++ ) {
if( (ret=usb_submit_urb(serial->port[i].read_urb)) != 0 ) {
dbg( "digi_startup_device: usb_submit_urb failed, port=%d,
ret=%d",
i, ret );
break;
}
}
device_startup = 1;
spin_unlock( &startup_lock );
return( ret );
}
static int digi_startup( struct usb_serial *serial )
{
int i;
digi_private_t *priv;
dbg( "digi_startup: TOP" );
spin_lock_init( &startup_lock );
/* allocate the private data structures for all ports */
/* number of regular ports + 1 for the out-of-band port */
for( i=0; i<digi_acceleport_device.num_ports+1; i++ ) {
serial->port[i].active = 0;
/* allocate private structure */
priv = serial->port[i].private =
(digi_private_t *)kmalloc( sizeof(digi_private_t),
GFP_KERNEL );
if( priv == (digi_private_t *)0 )
return( 1 ); /* error */
/* initialize private structure */
priv->dp_buf_len = 0;
priv->dp_modem_signals = 0;
spin_lock_init( &priv->dp_port_lock );
/* initialize write wait queue for this port */
init_waitqueue_head(&serial->port[i].write_wait);
}
/* initialize out of band port info */
oob_port_num = digi_acceleport_device.num_ports;
oob_port = &serial->port[oob_port_num];
device_startup = 0;
return( 0 );
}
static void digi_shutdown( struct usb_serial *serial )
{
int i;
dbg( "digi_shutdown: TOP" );
/* stop reads and writes on all ports */
for( i=0; i<digi_acceleport_device.num_ports+1; i++ ) {
usb_unlink_urb (serial->port[i].read_urb);
usb_unlink_urb (serial->port[i].write_urb);
}
device_startup = 0;
/* free the private data structures for all ports */
/* number of regular ports + 1 for the out-of-band port */
for( i=0; i<digi_acceleport_device.num_ports+1; i++ )
kfree( serial->port[i].private );
}
static void digi_read_bulk_callback( struct urb *urb )
{
struct usb_serial_port *port = (struct usb_serial_port *)urb->context;
struct usb_serial *serial = port->serial;
struct tty_struct *tty = port->tty;
int opcode = ((unsigned char *)urb->transfer_buffer)[0];
int len = ((unsigned char *)urb->transfer_buffer)[1];
int status = ((unsigned char *)urb->transfer_buffer)[2];
unsigned char *data = ((unsigned char *)urb->transfer_buffer)+3;
int ret,i;
dbg( "digi_read_bulk_callback: TOP: port=%d", port->number );
/* handle oob callback */
if( port->number == oob_port_num ) {
digi_read_oob( urb );
return;
}
/* sanity checks */
if( port_paranoia_check( port, "digi_read_bulk_callback" )
|| serial_paranoia_check( serial, "digi_read_bulk_callback" ) ) {
goto resubmit;
}
if( urb->status ) {
dbg( "digi_read_bulk_callback: nonzero read bulk status: %d",
urb->status );
goto resubmit;
}
#ifdef DEBUG_DATA
if( urb->actual_length ) {
printk( KERN_DEBUG __FILE__ ": digi_read_bulk_callback: port=%d, length=%d,
data=",
port->number, urb->actual_length );
for( i=0; i<urb->actual_length; ++i ) {
printk( "%.2x ", ((unsigned char *)urb->transfer_buffer)[i] );
}
printk( "\n" );
}
#endif
if( urb->actual_length != len + 2 )
err( KERN_INFO "digi_read_bulk_callback: INCOMPLETE PACKET, port=%d,
opcode=%d, len=%d, actual_length=%d, status=%d", port->number, opcode, len,
urb->actual_length, status );
/* receive data */
if( opcode == DIGI_CMD_RECEIVE_DATA && urb->actual_length > 3 ) {
len = MIN( len, urb->actual_length-3 );
for( i=0; i<len; ++i ) {
tty_insert_flip_char(tty, data[i], 0);
}
tty_flip_buffer_push(tty);
}
/* continue read */
resubmit:
if( (ret=usb_submit_urb(urb)) != 0 )
dbg( "digi_read_bulk_callback: failed resubmitting urb, ret=%d",
ret );
}
static void digi_read_oob( struct urb *urb )
{
struct usb_serial_port *port = (struct usb_serial_port *)urb->context;
struct usb_serial *serial = port->serial;
digi_private_t *priv;
int oob_opcode = ((unsigned char *)urb->transfer_buffer)[0];
int oob_line = ((unsigned char *)urb->transfer_buffer)[1];
int oob_status = ((unsigned char *)urb->transfer_buffer)[2];
int oob_ret = ((unsigned char *)urb->transfer_buffer)[3];
int ret;
dbg( "digi_read_oob: opcode=%d, line=%d, status=%d, ret=%d", oob_opcode, oob_line,
oob_status, oob_ret );
if( urb->status ) {
dbg( "digi_read_oob: nonzero read bulk status on oob: %d",
urb->status );
goto resubmit;
}
if( oob_opcode == DIGI_CMD_READ_INPUT_SIGNALS && oob_status == 0 ) {
priv = serial->port[oob_line].private;
spin_lock( &priv->dp_port_lock );
/* convert from digi flags to termiox flags */
if( oob_ret & DIGI_READ_INPUT_SIGNALS_CTS )
priv->dp_modem_signals |= TIOCM_CTS;
else
priv->dp_modem_signals &= ~TIOCM_CTS;
if( oob_ret & DIGI_READ_INPUT_SIGNALS_DSR )
priv->dp_modem_signals |= TIOCM_DSR;
else
priv->dp_modem_signals &= ~TIOCM_DSR;
if( oob_ret & DIGI_READ_INPUT_SIGNALS_RI )
priv->dp_modem_signals |= TIOCM_RI;
else
priv->dp_modem_signals &= ~TIOCM_RI;
if( oob_ret & DIGI_READ_INPUT_SIGNALS_DCD )
priv->dp_modem_signals |= TIOCM_CD;
else
priv->dp_modem_signals &= ~TIOCM_CD;
spin_unlock( &priv->dp_port_lock );
}
resubmit:
if( (ret=usb_submit_urb(urb)) != 0 ) {
dbg( "digi_read_oob: failed resubmitting oob urb, ret=%d",
ret );
}
}
#endif /* CONFIG_USB_SERIAL_DIGI_ACCELEPORT */
---------------------------------------------------------------------
To unsubscribe, e-mail: [EMAIL PROTECTED]
For additional commands, e-mail: [EMAIL PROTECTED]
