This patch cleans up the documentation of the device-tree binding for
the Flexcan devices on Freescale's PowerPC and ARM cores. Extra
properties are not used by the driver so we are removing them.
Signed-off-by: Robin Holt <h...@sgi.com>
Acked-by: Marc Kleine-Budde <m...@pengutronix.de>,
To: Wolfgang Grandegger <w...@grandegger.com>,
To: U Bhaskar-B22300 <b22...@freescale.com>
To: Scott Wood <scottw...@freescale.com>
To: Grant Likely <grant.lik...@secretlab.ca>
To: Kumar Gala <ga...@kernel.crashing.org>
Cc: socketcan-c...@lists.berlios.de,
Cc: net...@vger.kernel.org,
Cc: PPC list <linuxppc-dev@lists.ozlabs.org>
Cc: devicetree-disc...@lists.ozlabs.org
---
.../devicetree/bindings/net/can/fsl-flexcan.txt | 61 ++++----------------
arch/powerpc/boot/dts/p1010rdb.dts | 10 +---
arch/powerpc/boot/dts/p1010si.dtsi | 10 +--
3 files changed, 17 insertions(+), 64 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
index 1a729f0..80a78a9 100644
--- a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
+++ b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
@@ -1,61 +1,22 @@
-CAN Device Tree Bindings
-------------------------
-2011 Freescale Semiconductor, Inc.
+Flexcan CAN contoller on Freescale's ARM and PowerPC system-on-a-chip (SOC).
-fsl,flexcan-v1.0 nodes
------------------------
-In addition to the required compatible-, reg- and interrupt-properties, you can
-also specify which clock source shall be used for the controller.
+Required properties:
-CPI Clock- Can Protocol Interface Clock
- This CLK_SRC bit of CTRL(control register) selects the clock source to
- the CAN Protocol Interface(CPI) to be either the peripheral clock
- (driven by the PLL) or the crystal oscillator clock. The selected clock
- is the one fed to the prescaler to generate the Serial Clock (Sclock).
- The PRESDIV field of CTRL(control register) controls a prescaler that
- generates the Serial Clock (Sclock), whose period defines the
- time quantum used to compose the CAN waveform.
+- compatible : Should be "fsl,<processor>-flexcan" and "fsl,flexcan"
-Can Engine Clock Source
- There are two sources for CAN clock
- - Platform Clock It represents the bus clock
- - Oscillator Clock
+ An implementation should also claim any of the following compatibles
+ that it is fully backwards compatible with:
- Peripheral Clock (PLL)
- --------------
- |
- --------- -------------
- | |CPI Clock | Prescaler | Sclock
- | |---------------->| (1.. 256) |------------>
- --------- -------------
- | |
- -------------- ---------------------CLK_SRC
- Oscillator Clock
+ - fsl,p1010-flexcan
-- fsl,flexcan-clock-source : CAN Engine Clock Source.This property selects
- the peripheral clock. PLL clock is fed to the
- prescaler to generate the Serial Clock (Sclock).
- Valid values are "oscillator" and "platform"
- "oscillator": CAN engine clock source is
oscillator clock.
- "platform" The CAN engine clock source is the bus
clock
- (platform clock).
+- reg : Offset and length of the register set for this device
+- interrupts : Interrupt tuple for this device
-- fsl,flexcan-clock-divider : for the reference and system clock, an additional
- clock divider can be specified.
-- clock-frequency: frequency required to calculate the bitrate for FlexCAN.
+Example:
-Note:
- - v1.0 of flexcan-v1.0 represent the IP block version for P1010 SOC.
- - P1010 does not have oscillator as the Clock Source.So the default
- Clock Source is platform clock.
-Examples:
-
- can0@1c000 {
- compatible = "fsl,flexcan-v1.0";
+ can@1c000 {
+ compatible = "fsl,p1010-flexcan", "fsl,flexcan";
reg = <0x1c000 0x1000>;
interrupts = <48 0x2>;
interrupt-parent = <&mpic>;
- fsl,flexcan-clock-source = "platform";
- fsl,flexcan-clock-divider = <2>;
- clock-frequency = <fixed by u-boot>;
};
diff --git a/arch/powerpc/boot/dts/p1010rdb.dts
b/arch/powerpc/boot/dts/p1010rdb.dts
index 6b33b73..d6c669c 100644
--- a/arch/powerpc/boot/dts/p1010rdb.dts
+++ b/arch/powerpc/boot/dts/p1010rdb.dts
@@ -23,6 +23,8 @@
ethernet2 = &enet2;
pci0 = &pci0;
pci1 = &pci1;
+ can0 = &can0;
+ can1 = &can1;
};
memory {
@@ -169,14 +171,6 @@
};
};
- can0@1c000 {
- fsl,flexcan-clock-source = "platform";
- };
-
- can1@1d000 {
- fsl,flexcan-clock-source = "platform";
- };
-
usb@22000 {
phy_type = "utmi";
};
diff --git a/arch/powerpc/boot/dts/p1010si.dtsi
b/arch/powerpc/boot/dts/p1010si.dtsi
index 7f51104..f00076b 100644
--- a/arch/powerpc/boot/dts/p1010si.dtsi
+++ b/arch/powerpc/boot/dts/p1010si.dtsi
@@ -140,20 +140,18 @@
interrupt-parent = <&mpic>;
};
- can0@1c000 {
- compatible = "fsl,flexcan-v1.0";
+ can0: can@1c000 {
+ compatible = "fsl,p1010-flexcan", "fsl,flexcan";
reg = <0x1c000 0x1000>;
interrupts = <48 0x2>;
interrupt-parent = <&mpic>;
- fsl,flexcan-clock-divider = <2>;
};
- can1@1d000 {
- compatible = "fsl,flexcan-v1.0";
+ can1: can@1d000 {
+ compatible = "fsl,p1010-flexcan", "fsl,flexcan";
reg = <0x1d000 0x1000>;
interrupts = <61 0x2>;
interrupt-parent = <&mpic>;
- fsl,flexcan-clock-divider = <2>;
};
L2: l2-cache-controller@20000 {
--
1.7.2.1
_______________________________________________
Linuxppc-dev mailing list
Linuxppc-dev@lists.ozlabs.org
https://lists.ozlabs.org/listinfo/linuxppc-dev
