Thanks Eric, we tried a SiS 6326 and it worked great. We switched back to XF86_S3 driver for the Trio64 card and it works like it did under LTSP 2.06 (like we thought it would). The SiS booted up the lpp kernel great as well.
Thanks, James ----- Original Message ----- From: "Erick S. Tyack" <[EMAIL PROTECTED]> To: "James Newlin" <[EMAIL PROTECTED]> Sent: Wednesday, October 31, 2001 8:52 AM Subject: Re: [Ltsp-discuss] Re: 2.09pre4 > James, > > The S3 Trio64 chipset is not fully supported by XFree86 4.1. Only the Trio64 > 3D andTrio64 3D/2X are fully supported. If you have another video card on > hand, give it a try. It works very well for my SIS 6326 chipset. If you > didn't already look on their site, here is a link to the xfree86 driver > status list: http://www.xfree86.org/current/Status.html . > > Good luck, > > Erick > > On Wednesday 31 October 2001 06:56 am, you wrote: > > Thanks for the info, but that video mode comes back as invalid for my video > > card in the workstation. Its a S3 Trio64 PCI. The kernel thinks is VESA > > only, showing modes 0xF00 thru 0XF09. All either 80 columns or 132 > > columns. Perhaps we need another video card? > > > > ----- Original Message ----- > > From: "Erick S. Tyack" <[EMAIL PROTECTED]> > > To: "James Newlin" <[EMAIL PROTECTED]>; "LTSP Discuss Group" > > <[EMAIL PROTECTED]> > > Sent: Tuesday, October 30, 2001 5:39 PM > > Subject: Re: [Ltsp-discuss] Re: 2.09pre4 > > > > > James, > > > > > > You also need the following lines for each workstation in your dhcpd.conf > > > file in order for the lpp screen to display: > > > > > > option option-128 e4:45:74:68:00:00; > > > option option-129 "vga=0x301 console=/dev/tty2"; > > > > > > Hope this helps, > > > > > > Erick > > > > > > On Tuesday 30 October 2001 05:26 pm, James Newlin wrote: > > > > When we added "option log-servers" in the dhcpd.conf the workstation > > > > continued to boot up. > > > > > > > > ----- Original Message ----- > > > > From: "James Newlin" <[EMAIL PROTECTED]> > > > > To: "LTSP Discuss Group" <[EMAIL PROTECTED]> > > > > Sent: Tuesday, October 30, 2001 3:32 PM > > > > Subject: 2.09pre4 > > > > > > > > > We are sorry if this has already been addressed and answered... We > > > > > have installed 2.09pre4. Install appeared to be perfect. We are > > > > using > > > > > > RedHat > > > > > > > > > 7.0 distro. Workstation boots but stops at the NFS mount saying > > > > > > > > "nfsmount > > > > > > > > > failed: bad file number" and "NFS: mount program didn't pass remote > > > > > address!". We must be missing something. Any ideas? We > > > > > have NFS running and exports shows the correct path names and IP > > > > > addresses. We > > > > > > > > are > > > > > > > > > using ISC dhcp 3.0rc12. Our dhcpd.conf has the option root-path > > > > > > > > statement > > > > > > > > > using "192.168.1.1:/opt/ltsp/i386". Also when we use the lpp > > > > kernel, > > > > > > > it asks us for a video mode? Any video mode we choose, does not > > > > bring > > > > > > > up > > > > > > > > the > > > > > > > > > pretty "LTSP booting" screen. Do we send something in the > > > > dhcpd.conf > > > > > > file > > > > > > > > > to set the video mode? > > > > > > > > > > Thanks for your time, > > > > > > > > > > James > > > > > > > > _____________________________________________________________________ > > > > Ltsp-discuss mailing list. To un-subscribe, or change prefs, goto: > > > > https://lists.sourceforge.net/lists/listinfo/ltsp-discuss > > > > For additional LTSP help, try #ltsp channel on irc.openprojects.net > > > > > > -- > > > Acurrus Consulting, LLC > > > 22969 Allen Rd., St. Clair Shores, MI 48080 > > > PH: 810.801.0004 > > > Fax: 810.447.5458 > > > emailto [EMAIL PROTECTED] > > -- > Acurrus Consulting, LLC > 22969 Allen Rd., St. Clair Shores, MI 48080 > PH: 810.801.0004 > Fax: 810.447.5458 > emailto [EMAIL PROTECTED] _____________________________________________________________________ Ltsp-discuss mailing list. To un-subscribe, or change prefs, goto: https://lists.sourceforge.net/lists/listinfo/ltsp-discuss For additional LTSP help, try #ltsp channel on irc.openprojects.net
