Davo ,
L18 with Delorto, prolly look outa place next to WRX and the rest.
>From: "Davo" <[EMAIL PROTECTED]>
>Reply-To: [EMAIL PROTECTED]
>To: <[EMAIL PROTECTED]>
>Subject: Re: Exhaust enineering
>Date: Fri, 5 May 2000 19:17:02 +1000
>
>We dont have a DB meter at work, sorry, but im sure they could figure
>something out. Its called HI-Tech mufflers 744 parramatta road, Lewisham.
>We get alot of WRX's, Skyline GTR's, Supra's etc so it would be good to see
>a datto for a change. We just did a 350chev torana which im sure was well
>over 100db with the full system on. What engine do u have???
>
>Davo
>
>-----Original Message-----
>From: Craig Harris <[EMAIL PROTECTED]>
>To: [EMAIL PROTECTED] <[EMAIL PROTECTED]>
>Date: Friday, 5 May 2000 6:50
>Subject: Re: Exhaust enineering
>
>
> >
> >Davo im in Sydney near chatswood. ive been calling a few places but not
>many
> >have a DB meter, does your work have one? i think ill try and persuade my
> >engo to swap the resonator for a muffler and leave it at that but if your
> >work isnt far (no rego) ill take it to your place forsure.
> >
> >Cheers Craig
> >
> >>From: "Davo" <[EMAIL PROTECTED]>
> >>Reply-To: [EMAIL PROTECTED]
> >>To: <[EMAIL PROTECTED]>
> >>Subject: Re: Exhaust enineering
> >>Date: Fri, 5 May 2000 18:08:29 +1000
> >>
> >>Craig, were r u? I could get the boys at work to have look at it. I
>work
> >>at a Exhaust joint in Sydney.
> >>
> >>-----Original Message-----
> >>From: Craig Harris <[EMAIL PROTECTED]>
> >>To: [EMAIL PROTECTED] <[EMAIL PROTECTED]>
> >>Date: Thursday, 4 May 2000 7:05
> >>Subject: Exhaust enineering
> >>
> >>
> >> >
> >> >
> >> >
> >> >Gday
> >> >
> >> >my engineer came round today and everything went sweet until he
>measured
> >>the
> >> >DB reading on the exhaust 102 DB which is something like 30% over. My
> >> >question is if i have a muffler & a hotdog what should i do ? swap the
> >>dog
> >> >for another muffler or get another muffler installed somewhere?
> >> >Im not keen for that last one but i dont want to mess around with
> >>different
> >> >combinations if possible.
> >> >
> >> >On a side note if an L18 is bored to 86mm with a standard crank and
>rod
> >> >setup whats the new displacement?
> >> >
> >> >cheers Craig
> >>
> >________________________________________________________________________
> >> >Get Your Private, Free E-mail from MSN Hotmail at
>http://www.hotmail.com
> >> >
> >> >--membersozdat-------------------------------------------------------
> >> >OZDAT Mailing List Please Note:-
> >> >Send (un)subscribe requests to [EMAIL PROTECTED]
> >> >Send submissions to [EMAIL PROTECTED]
> >> >No unauthorised redistribution of this email
> >> >http://www.datascribe.com.au/ozdatonline/index.htm
> >> >http://www.datascribe.com.au/ozdatonline/listindex.html
> >> >---------------------------------------------------------------------
> >>
> >
> >________________________________________________________________________
> >Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com
> >
>
________________________________________________________________________
Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com
--membersozdat-------------------------------------------------------
OZDAT Mailing List Please Note:-
Send (un)subscribe requests to [EMAIL PROTECTED]
Send submissions to [EMAIL PROTECTED]
No unauthorised redistribution of this email
http://www.datascribe.com.au/ozdatonline/index.htm
http://www.datascribe.com.au/ozdatonline/listindex.html
http://www.mail-archive.com/[email protected]/
---------------------------------------------------------------------
