Yep the 4340 housings work well Toby. After you replace the housing, the next thing to give is the bearing carrier spigots but by then you are putting some very serious grunt through the diff.
Cheers, Feral Errol <http://www.datrats.com.au/> -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of tobias walker Sent: Saturday, September 07, 2002 11:53 PM To: [EMAIL PROTECTED] Subject: RE: LSDs there is machined steel hemispheres floating here in QLD made out of billet 4340 I think for about 500 with end plate for thouse wo crack there R180 s apart and what the indestructible option errol >From: "E Smith" <[EMAIL PROTECTED]> >Reply-To: [EMAIL PROTECTED] >To: <[EMAIL PROTECTED]> >Subject: RE: LSDs >Date: Thu, 5 Sep 2002 13:33:34 +1000 > >Rob P >An R180 will handle most N/A engines happily, but if you get a bit of boost >on a turbo engine they will split the hemispheres with big torque engines. >An R200 is infinitely more reliable in any application with a bit of grunt. >They used R200's as stock in later Z's and an R200 Clutch pack in S12 >silvias behind CA18DET's so why would nissan waste money if they thought >they could get away with an R180LSD. >The 720 ute 4WD has an R180 fron tdif but is not LSD stock. >It was a dealer fitted option if required for $3500. > Cheers, Feral Errol >[EMAIL PROTECTED] > >WWW.datrats.com.au > >-----Original Message----- >From: [EMAIL PROTECTED] >[mailto:[EMAIL PROTECTED]]On Behalf Of Rob P >Sent: Thursday, 5 September 2002 1:06 PM >To: [EMAIL PROTECTED] >Subject: LSDs > > >Anyway isnt a R200 a bit of overkill? do you plan on putting more than >450HP >through it? >I thought even a R180 could handle up to 400HP easy! I just bought an open >R180 5.1 ratio diff for my 1600, >yet to be installed. I figure it might be good for motorkhanas even though >I'll forfeit top speed a bit. > >BTW, I keep hearing rumours that a 720 4WD ute (front?) diff is LSD. Anyone >know if this is true? >Is it R180? What ratio? So many questions. > > >my 2 cents worth > >Rob P >----- Original Message ----- > From: E Smith > To: [EMAIL PROTECTED] > Sent: Thursday, September 05, 2002 10:44 AM > Subject: RE: S13 Lsds > > > Ben, > Dont bother with the S13 R200 as they are crap by comparison with clutch >pack centres and are a lot harder to fit. > > Cheers, Feral Errol > [EMAIL PROTECTED] > > WWW.datrats.com.au > > -----Original Message----- > From: [EMAIL PROTECTED] >[mailto:[EMAIL PROTECTED]]On Behalf Of Ben C > Sent: Thursday, 5 September 2002 10:20 AM > To: [EMAIL PROTECTED] > Subject: Re: S13 Lsds > > > im gunan be putting c210 IRS in the bluey later on.....how difficult >would >it be fitting a s13/r32/33 R200 into the setup??? > ----- Original Message ----- > From: E Smith > To: [EMAIL PROTECTED] > Sent: Thursday, September 05, 2002 7:01 AM > Subject: RE: S13 Lsds > > > The later S13 style viscous LSD uses a left side axle with 2 sets of >slpines on it. One spline connect to the side gear and the second set of >splines to the viscous clutch pack. The Viscous clutch pack is only >approximately 12 mm thick and wea out very quickly with any decent torque >put through them. Also the make them work you must use the axles that came >with the centre. Also there are two spline distances on the left axle >depending on model. All to much trouble. > I also looked at changing the later viscous diffs to early clutch >pack, >but this is also a pain due to crown wheel offset distances being >different. > Cheers, Feral Errol > [EMAIL PROTECTED] > > WWW.datrats.com.au > > --membersozdat------------------------------------------------------- > OZDAT Mailing List Please Note:- > Send (un)subscribe requests to [EMAIL PROTECTED] > Send submissions to [EMAIL PROTECTED] > No unauthorised redistribution of this email > http://www.ozdat.com/ozdatonline/index.htm > http://www.ozdat.com/ozdatonline/listindex.html > http://www.mail-archive.com/[email protected]/ > --------------------------------------------------------------------- > > --membersozdat------------------------------------------------------- > OZDAT Mailing List Please Note:- > Send (un)subscribe requests to [EMAIL PROTECTED] > Send submissions to [EMAIL PROTECTED] > No unauthorised redistribution of this email > http://www.ozdat.com/ozdatonline/index.htm > http://www.ozdat.com/ozdatonline/listindex.html > http://www.mail-archive.com/[email protected]/ > --------------------------------------------------------------------- > --membersozdat------------------------------------------------------- > OZDAT Mailing List Please Note:- > Send (un)subscribe requests to [EMAIL PROTECTED] > Send submissions to [EMAIL PROTECTED] > No unauthorised redistribution of this email > http://www.ozdat.com/ozdatonline/index.htm > http://www.ozdat.com/ozdatonline/listindex.html > http://www.mail-archive.com/[email protected]/ > --------------------------------------------------------------------- > >--membersozdat------------------------------------------------------- >OZDAT Mailing List Please Note:- >Send (un)subscribe requests to [EMAIL PROTECTED] >Send submissions to [EMAIL PROTECTED] >No unauthorised redistribution of this email >http://www.ozdat.com/ozdatonline/index.htm >http://www.ozdat.com/ozdatonline/listindex.html >http://www.mail-archive.com/[email protected]/ >--------------------------------------------------------------------- > ><< FeralErrol.vcf >> _________________________________________________________________ Join the world�s largest e-mail service with MSN Hotmail. http://www.hotmail.com --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/[email protected]/ ---------------------------------------------------------------------
