sorry this car has a 16v motor. i have been driving it for a couple months so the noise and loping is definately different and made me want to shut the car off.
no ac hardware installed i think somebody yanked it and did things the wrong way. i got a bently manual and assume i will have to break things down to check, i guess i was just looking for some real world experience. i just assumed something was getting jammed up in a way to put load on the timing belt side to make it lope at idle. but that coupled with the oil light and shavings near the im shaft makes me fear its the engine side. i can't even move a pulley when tugging by hand right now. i had a diesel vacuum pump sieze up once and stopped the im shaft dead. you could hear the belt screeching, oil light went off and you could smell the belt. that was the craziest thing i have ever seen, was using a rotary type and the gear shaved grooves into the cover. after i got it towed home last night i had to start it and move it onto the driveway. started and ran as normal with no oil pressure light but i didn't want to warm it up. wasn't loping but all the clattery racket/scratching can be heard especially after stabbing the throttle and letting off. On Thursday, December 24, 2015 at 10:35:01 PM UTC-8, stevenarguello wrote: > > The 8v distributor runs off of the intermediate shaft along with the oil > pump. If it jumped a tooth or two the spark timing would be off. The 16v > dizzy runs off the cam. > Does it have A/C? > > > > On Dec 24, 2015, at 12:22 PM, damac2004 <dama...@sbcglobal.net > <javascript:>> wrote: > > I'm new to these cars. I got one of these a few months ago and planned on > using it as a project to restore for fun. I have been driving it as is > because it worked. I do have to get it smogged and clean up some neglect > but it was getting me around ok with no funky noises. > > Yesterday I came off the freeway and all of a sudden the high pressure oil > buzzer constantly started going off. I heard a racket of screeches and > clunks in the engine bay and the engine was loping near idle speed. So too > many wierd things at once to ignore, but I had to get off the road so i > probably ran the car about a minute after before turning it off. just > putting my safety first because of where i was vs. potentially blowing up a > motor. > > i had to work and came back to cold car. i have good fluids and started > it up for a bit. it ran with just the hint of stumbling although i don't > know if these cars typically do that while warming up. it wasn't loping > the same. i reved it and didn't get the light to come on but noticed the > racket sounded like its on the drive belt system. while engine was running > only odd thing i noticed is shavings i think near the intermediate shaft > from the lower plastic timing belt cover. couldn't quite tell if another > pully was actually touching it. > > im i correct to assume that if something in vbelt system dragged all it > would do is slow down the timing belt, but that would still turn the im > shaft without interference? > > is it possible a pulley wobbled its way into the im shaft and held it up? > i sure didn't smell smoking timing belt and will have to look closer. it > has power steering, alternator, water pump with 2 vbelts. > > or maybe something bad happned inside engine with oil pump or the im > bearings and the pulley side is worn and walking out and hitting? > > -- > You received this message because you are subscribed to the Google Groups > "MK2-16v" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to mk2-16v+u...@googlegroups.com <javascript:>. > To post to this group, send email to mk2...@googlegroups.com <javascript:> > . > Visit this group at https://groups.google.com/group/mk2-16v. > To view this discussion on the web visit > https://groups.google.com/d/msgid/mk2-16v/af959f0b-50cd-474c-917b-f978104e7adb%40googlegroups.com > > <https://groups.google.com/d/msgid/mk2-16v/af959f0b-50cd-474c-917b-f978104e7adb%40googlegroups.com?utm_medium=email&utm_source=footer> > . > For more options, visit https://groups.google.com/d/optout. > -- You received this message because you are subscribed to the Google Groups "MK2-16v" group. To unsubscribe from this group and stop receiving emails from it, send an email to mk2-16v+unsubscr...@googlegroups.com. To post to this group, send email to mk2-16v@googlegroups.com. Visit this group at https://groups.google.com/group/mk2-16v. To view this discussion on the web visit https://groups.google.com/d/msgid/mk2-16v/64bed5b2-e9a0-4945-bf86-26e23998cd74%40googlegroups.com. For more options, visit https://groups.google.com/d/optout.
