Hello Siva, unfortunately I am not familiar with ARM linux, so I cannot help you here.
Regards Sebastian On Friday, March 3, 2017 at 11:59:31 AM UTC+1, Siva Prasad Meduri wrote: > > Hi Sebastian > > > > Thanks a lot for your valuable reply. It helped me a lot. > > > > I am trying to compile openwrt mcproxy for ARM linux . > > > > When I try to compile mcproxy using below commands, it is compiling for > x86. > > 1. qmake mcproxy.pro > > 2. Make > > > > But my requirement is to compile for ARM . Could you please help me with > the Makefile , or the how to generate ARM compatible makefile from qmake . > > > > Please help me in this issue. > > Regards > > Siva Prasad > > > > > > *From:* Sebastian Woelke [mailto:[email protected]] > *Sent:* Thursday, March 02, 2017 2:59 PM > *To:* Multicast Proxy <[email protected]> > *Cc:* Siva Prasad Meduri <[email protected]> > *Subject:* Re: Does mcproxy support IGMPv3(source specific multicast ) ? > > > > Hello Siva, > > here is an example of how to configure Mcproxy: > https://github.com/mcproxy/mcproxy/blob/master/mcproxy/mcproxy.conf > > In detail you have to set the group management protocol the proxy shall > use ("IGMPv3" for IPv4 or "MLDv2" for IPv6) > and you have to configure upstream interface and downstream interfaces. > > Your config file could like like this: > > protocol IGMPv3; > pinstance myProxy: eth0 ==> eth1 eth2; > > > Regards > Sebastian > > On Thursday, March 2, 2017 at 9:41:52 AM UTC+1, Siva Prasad Meduri wrote: > > > > Hi Sebastian > > > > I am using mcproxy for openwrt routers . I am finding difficulty in > configuring mcproxy . > > > > Could you please help in basic configuration of mcproxy . > > > > Thanks > > > > Regards > > Siva Prasad > > > > > > *From:* Siva Prasad Meduri > *Sent:* Monday, February 13, 2017 7:41 PM > *To:* '[email protected]' <[email protected]>; > 'Sebastian Woelke' <[email protected]> > *Subject:* RE: Does mcproxy support IGMPv3(source specific multicast ) ? > > > > Hi Sebastian > > > > I am using mcproxy for openwrt routers . I am finding difficulty in > configuring mcproxy . > > > > Could you please help in basic configuration of mcproxy . > > > > Thanks > > > > Regards > > Siva Prasad > > > > *From:* Siva Prasad Meduri > *Sent:* Monday, February 06, 2017 2:03 PM > *To:* '[email protected]' <[email protected] > > > *Subject:* Does mcproxy support IGMPv3(source specific multicast ) ? > > > > Hi Admin > > > > I am currently working on latest mcproxy (downloaded from > https://github.com/mcproxy/mcproxy ) > > > > Please help me with the following queries > > > > 1. Does this mcproxy support IGMPv3 ? (Source specific multicast ). > Please help me in understanding to what extent mcproxy supports IGMPv3 > (source specific multicast ) and limitations if any . > > 2. I see the mcproxy source code is written in CPP . Is the code > available in C programming language ?. > > > > Please help me with the following queries > > > > Thanks > > > > > > Regards > > Siva Prasad > > > > -- You received this message because you are subscribed to the Google Groups "Multicast Proxy" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
