Hi Siva, there already is support for mcproxy in OpenWRT [1], so you should be able to install it via opkg or lucy.
If you want to build a custom version of mcproxy for your specific OpenWRT platform, you have to use the OpenWRT SDK [2]. I'm quite certain, that simply cross compiling mcproxy for ARM will work with OpenWRT. OpenWRT runs on many different ARM-based routers, the SDK provides a toolchain to build the base system and required packages. [1]: https://github.com/openwrt-routing/packages/tree/master/mcproxy [2]: https://wiki.openwrt.org/doc/howto/obtain.firmware.sdk Hope this gets you started, best, Sebastian (another one :) > Am 03.03.2017 um 11:38 schrieb Siva Prasad Meduri <[email protected]>: > > Hi Sebastian > > Thanks a lot for your valuable reply. It helped me a lot. > > I am trying to compile openwrt mcproxy for ARM linux . > > When I try to compile mcproxy using below commands, it is compiling for x86. > 1. qmake mcproxy.pro > 2. Make > > But my requirement is to compile for ARM . Could you please help me with the > Makefile , or the how to generate ARM compatible makefile from qmake . > > Please help me in this issue. > > Regards > Siva Prasad > > > From: Sebastian Woelke [mailto:[email protected]] > Sent: Thursday, March 02, 2017 2:59 PM > To: Multicast Proxy <[email protected]> > Cc: Siva Prasad Meduri <[email protected]> > Subject: Re: Does mcproxy support IGMPv3(source specific multicast ) ? > > Hello Siva, > > here is an example of how to configure Mcproxy: > https://github.com/mcproxy/mcproxy/blob/master/mcproxy/mcproxy.conf > > In detail you have to set the group management protocol the proxy shall use > ("IGMPv3" for IPv4 or "MLDv2" for IPv6) > and you have to configure upstream interface and downstream interfaces. > > Your config file could like like this: > protocol IGMPv3; > pinstance myProxy: eth0 ==> eth1 eth2; > > Regards > Sebastian > > On Thursday, March 2, 2017 at 9:41:52 AM UTC+1, Siva Prasad Meduri wrote: > > Hi Sebastian > > I am using mcproxy for openwrt routers . I am finding difficulty in > configuring mcproxy . > > Could you please help in basic configuration of mcproxy . > > Thanks > > Regards > Siva Prasad > > > From: Siva Prasad Meduri > Sent: Monday, February 13, 2017 7:41 PM > To: '[email protected]' <[email protected]>; > 'Sebastian Woelke' <[email protected]> > Subject: RE: Does mcproxy support IGMPv3(source specific multicast ) ? > > Hi Sebastian > > I am using mcproxy for openwrt routers . I am finding difficulty in > configuring mcproxy . > > Could you please help in basic configuration of mcproxy . > > Thanks > > Regards > Siva Prasad > > From: Siva Prasad Meduri > Sent: Monday, February 06, 2017 2:03 PM > To: '[email protected]' <[email protected]> > Subject: Does mcproxy support IGMPv3(source specific multicast ) ? > > Hi Admin > > I am currently working on latest mcproxy (downloaded from > https://github.com/mcproxy/mcproxy ) > > Please help me with the following queries > > 1. Does this mcproxy support IGMPv3 ? (Source specific multicast ). > Please help me in understanding to what extent mcproxy supports IGMPv3 > (source specific multicast ) and limitations if any . > > 2. I see the mcproxy source code is written in CPP . Is the code > available in C programming language ?. > > > Please help me with the following queries > > Thanks > > > Regards > Siva Prasad > > > -- > You received this message because you are subscribed to the Google Groups > "Multicast Proxy" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > For more options, visit https://groups.google.com/d/optout. Sebastian Meiling +---------------------------------------+ Internet Technologies Group Department of Computer Science Hamburg University of Applied Sciences Berliner Tor 7, 20099 Hamburg, Germany +---------------------------------------+ Mail: [email protected] Fon: +49 40 42875 - 8067 Fax: +49 40 42875 - 8409 Web: http://www.haw-hamburg.de/inet +---------------------------------------+ -- You received this message because you are subscribed to the Google Groups "Multicast Proxy" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
