Hi Siva, yes, Mcproxy can interoperate with the older version IGMPv2.
I hope this helps. Regards Sebastian On Thursday, March 30, 2017 at 11:11:03 AM UTC+2, Siva Prasad Meduri wrote: > > Hi Sebestian > > > > Thanks a lot for the reply. Yes, it is working now. > > > > I have one more query. > > When I use protocol as IGMPv3, and connect two downstream interfaces ,(one > host using IGMPv2 and the other IGMPv3), > > > > root@OpenWrt:~# cat /etc/mcproxy.conf > > protocol IGMPv3; > > pinstance myproxy: “eth0” ==> “eth2.1” “eth2.2”; > > > > Here host connected to eth2.1 sends IGMPv2 packets, host connect to eth2.2 > sends IGMPV3 packets. Does mcproxy forward to both the hosts ? > > Please help me in this issue. > > Regards > > Siva Prasad > > > > *From:* Sebastian Woelke [mailto:[email protected]] > *Sent:* Thursday, March 30, 2017 1:53 PM > *To:* Multicast Proxy <[email protected]> > *Cc:* G Vidya Sankar Gottumukkula <[email protected]>; Ganesh > Reddy <[email protected]>; Siva Prasad Meduri <[email protected]> > *Subject:* Re: Does mcproxy support IGMPv3(source specific multicast ) ? > > > > Hi Siva, > > quotes around eth2.1 should solve the problem. > > Like this: > > protocol IGMPv3; > > pinstance myproxy: eth0 ==> "eth2.1"; > > > Regards > Sebastian > > On Thursday, March 30, 2017 at 10:09:38 AM UTC+2, Siva Prasad Meduri wrote: > > Hi Sebastian > > > > Thanks a lot for your valuable reply . > > > > I have configured mcproxy in the following way and run the mcproxy binary > as shown below : > > > > root@OpenWrt:~# cat /etc/mcproxy.conf > > protocol IGMPv3; > > pinstance myproxy: eth0 ==> eth2.1; > > > > root@OpenWrt:~# /usr/local/bin/mcproxy -dsvv -f /etc/mcproxy.conf > > ERROR: failed to parse line 2 unknown token TT_DOT with value in this > context > > failed to parse config file > > > > But I get the above error marked in yellow, when I configure eth0 as > upstream and eth2.1 as downstream interfaces. I think it’s a parsing error > in mcproxy.conf but the syntax I followed seems correct. > > > > Could you please help me resolve this issue. > > > > > > Regards > > Siva Prasad > > > > *From:* Sebastian Woelke [mailto:[email protected]] > *Sent:* Thursday, March 02, 2017 2:59 PM > *To:* Multicast Proxy <[email protected]> > *Cc:* Siva Prasad Meduri <[email protected]> > *Subject:* Re: Does mcproxy support IGMPv3(source specific multicast ) ? > > > > Hello Siva, > > here is an example of how to configure Mcproxy: > https://github.com/mcproxy/mcproxy/blob/master/mcproxy/mcproxy.conf > > In detail you have to set the group management protocol the proxy shall > use ("IGMPv3" for IPv4 or "MLDv2" for IPv6) > and you have to configure upstream interface and downstream interfaces. > > Your config file could like like this: > > protocol IGMPv3; > pinstance myProxy: eth0 ==> eth1 eth2; > > > Regards > Sebastian > > On Thursday, March 2, 2017 at 9:41:52 AM UTC+1, Siva Prasad Meduri wrote: > > > > Hi Sebastian > > > > I am using mcproxy for openwrt routers . I am finding difficulty in > configuring mcproxy . > > > > Could you please help in basic configuration of mcproxy . > > > > Thanks > > > > Regards > > Siva Prasad > > > > > > *From:* Siva Prasad Meduri > *Sent:* Monday, February 13, 2017 7:41 PM > *To:* '[email protected]' <[email protected]>; > 'Sebastian Woelke' <[email protected]> > *Subject:* RE: Does mcproxy support IGMPv3(source specific multicast ) ? > > > > Hi Sebastian > > > > I am using mcproxy for openwrt routers . I am finding difficulty in > configuring mcproxy . > > > > Could you please help in basic configuration of mcproxy . > > > > Thanks > > > > Regards > > Siva Prasad > > > > *From:* Siva Prasad Meduri > *Sent:* Monday, February 06, 2017 2:03 PM > *To:* '[email protected]' <[email protected] > > > *Subject:* Does mcproxy support IGMPv3(source specific multicast ) ? > > > > Hi Admin > > > > I am currently working on latest mcproxy (downloaded from > https://github.com/mcproxy/mcproxy ) > > > > Please help me with the following queries > > > > 1. Does this mcproxy support IGMPv3 ? (Source specific multicast ). > Please help me in understanding to what extent mcproxy supports IGMPv3 > (source specific multicast ) and limitations if any . > > 2. I see the mcproxy source code is written in CPP . Is the code > available in C programming language ?. > > > > Please help me with the following queries > > > > Thanks > > > > > > Regards > > Siva Prasad > > > > -- You received this message because you are subscribed to the Google Groups "Multicast Proxy" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
