Hi Siva,
we do have a number of other people in the group who are familiar with
OpenWRT on Arm.
We'll try to address your problem.
Best,
Thomas
On 03.03.2017 12:06, Sebastian Woelke wrote:
Hello Siva,
unfortunately I am not familiar with ARM linux, so I cannot help you here.
Regards
Sebastian
On Friday, March 3, 2017 at 11:59:31 AM UTC+1, Siva Prasad Meduri wrote:
Hi Sebastian
Thanks a lot for your valuable reply. It helped me a lot.
I am trying to compile openwrt mcproxy for ARM linux .
When I try to compile mcproxy using below commands, it is compiling
for x86.
1. qmake mcproxy.pro <http://mcproxy.pro>
2. Make
But my requirement is to compile for ARM . Could you please help me
with the Makefile , or the how to generate ARM compatible makefile
from qmake .
Please help me in this issue.
Regards
Siva Prasad
*From:*Sebastian Woelke [mailto:[email protected]
<mailto:[email protected]>]
*Sent:* Thursday, March 02, 2017 2:59 PM
*To:* Multicast Proxy <[email protected]
<mailto:[email protected]>>
*Cc:* Siva Prasad Meduri <[email protected]
<mailto:[email protected]>>
*Subject:* Re: Does mcproxy support IGMPv3(source specific multicast ) ?
Hello Siva,
here is an example of how to configure Mcproxy:
https://github.com/mcproxy/mcproxy/blob/master/mcproxy/mcproxy.conf
<https://github.com/mcproxy/mcproxy/blob/master/mcproxy/mcproxy.conf>
In detail you have to set the group management protocol the proxy
shall use ("IGMPv3" for IPv4 or "MLDv2" for IPv6)
and you have to configure upstream interface and downstream interfaces.
Your config file could like like this:
protocol IGMPv3;
pinstance myProxy: eth0 ==> eth1 eth2;
Regards
Sebastian
On Thursday, March 2, 2017 at 9:41:52 AM UTC+1, Siva Prasad Meduri
wrote:
Hi Sebastian
I am using mcproxy for openwrt routers . I am finding difficulty
in configuring mcproxy .
Could you please help in basic configuration of mcproxy .
Thanks
Regards
Siva Prasad
*From:* Siva Prasad Meduri
*Sent:* Monday, February 13, 2017 7:41 PM
*To:* '[email protected]
<mailto:[email protected]>'
<[email protected]
<mailto:[email protected]>>; 'Sebastian Woelke'
<[email protected] <mailto:[email protected]>>
*Subject:* RE: Does mcproxy support IGMPv3(source specific
multicast ) ?
Hi Sebastian
I am using mcproxy for openwrt routers . I am finding difficulty
in configuring mcproxy .
Could you please help in basic configuration of mcproxy .
Thanks
Regards
Siva Prasad
*From:* Siva Prasad Meduri
*Sent:* Monday, February 06, 2017 2:03 PM
*To:* '[email protected]
<mailto:[email protected]>'
<[email protected]
<mailto:[email protected]>>
*Subject:* Does mcproxy support IGMPv3(source specific multicast ) ?
Hi Admin
I am currently working on latest mcproxy (downloaded from
https://github.com/mcproxy/mcproxy
<https://github.com/mcproxy/mcproxy> )
Please help me with the following queries
1. Does this mcproxy support IGMPv3 ? (Source specific
multicast ). Please help me in understanding to what extent
mcproxy supports IGMPv3 (source specific multicast ) and
limitations if any .
2. I see the mcproxy source code is written in CPP . Is
the code available in C programming language ?.
Please help me with the following queries
Thanks
Regards
Siva Prasad
--
You received this message because you are subscribed to the Google
Groups "Multicast Proxy" group.
To unsubscribe from this group and stop receiving emails from it, send
an email to [email protected]
<mailto:[email protected]>.
For more options, visit https://groups.google.com/d/optout.
--
Prof. Dr. Thomas C. Schmidt
° Hamburg University of Applied Sciences Berliner Tor 7 °
° Dept. Informatik, Internet Technologies Group 20099 Hamburg, Germany °
° http://www.haw-hamburg.de/inet Fon: +49-40-42875-8452 °
° http://www.informatik.haw-hamburg.de/~schmidt Fax: +49-40-42875-8409 °
--
You received this message because you are subscribed to the Google Groups "Multicast
Proxy" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
For more options, visit https://groups.google.com/d/optout.
