The BusID thing varies. I've seen many variations. Try

BusID "0:13:0"

BusID "PCI:0:0xd:0"

BusID "0:0xd:0"


--- Shalem Shem-Tov <[EMAIL PROTECTED]> wrote:

> From: Tim Fenn <[EMAIL PROTECTED]>
> Reply To: Discussion about mythtv
> <mythtv-users@mythtv.org>
> To: Discussion about mythtv
> <mythtv-users@mythtv.org>
> Subject: Re: [mythtv-users] X to TVout on pvr350
> Sent: Thursday, February 17, 2005 10:04 PM
> 
> On Thu, Feb 17, 2005 at 09:39:10PM -0500, Shalem
> Shem-Tov wrote:
> >OK having some problems getting X to TVout on
> pvr350 (using Fedora C3).  I 
> >followed Jarod's HOWTO on how to change xorg.conf
> but once I did and tried 
> >to reload X I got this error:
> >
> >Failed to load module "ivtvdev" (module does not
> exist, 0)
> >No drivers available
> >
> >
> >ATrpms now has the ivtvdev driver in its own
> package - this is a
> >change that I don't think has made it into Jarod's
> howto quite yet.
> >Anyway, long story short:
> >
> >apt-get install ivtvdev
> >
> >should fix this (assuming you have Axel's repo
> enabled).
> >
> >Regards,
> >-Tim
> 
> 
> Tim:
> Thanks for the info, it help... to a point.  Now
> when I try loading X I get 
> this error:
> 
>        ivtvdev: No matching Device section for
> instance (BusID PCI:0:13:0)
>        No devices detected.
> 
> /sbin/lspci -v  gives me:
> 
> 00:0d.0 Multimedia video controller: Internext
> Compression Inc iTVC15 MPEG-2 
> Encoder(rev 01)
>         Subsystem: Hauppauge computer works Inc.
> WinTV PVR-350
>         Flags: bus master, medium devsel, latency
> 64, IRQ 10
>         Memory at d8000000 (32-bit, prefetchable)
> [size=64M]
>         Capabilities: [44] Power Management version
> 2
> 
> 
> Any suggestions?
> 
> My xorg.conf is the same as before:
> 
> Section "Device"
>        Identifier  "Hauppauge PVR 350 iTVC15
> Framebuffer"
>        Driver      "ivtvdev"
>        #Driver      "fbdev"
> 
>        ### change fb0 to whatever your card grabbed
>        Option      "fbdev" "/dev/fb1"
> 
>        ### change the BusID to whatever is reported
> by lspci, specify it as 
> hex.
>        BusID "0:0x0d:0"
> EndSection
> 
> Thanks :)
> 
> 
> > _______________________________________________
> mythtv-users mailing list
> mythtv-users@mythtv.org
>
http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
> 



                
__________________________________ 
Do you Yahoo!? 
Read only the mail you want - Yahoo! Mail SpamGuard. 
http://promotions.yahoo.com/new_mail 
_______________________________________________
mythtv-users mailing list
mythtv-users@mythtv.org
http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users

Reply via email to