Ok, that could potentially be IC # U-4 on the master module. It's an
NE-5532 dual op-amp, 8 pin DIP package. It's socketed so you should be
able to pry it out with a little screw driver and put the new one in.
MAKE SURE you put it in the right way up (the dot or notch on the end
should face the top of the module) That would be the master module, BTW,
the chip should be right under the "Aux A" master pot. If you are not
sure what you are doing, get help. Also, make sure that all eight pins
of the IC go into the socket and don't bend under it or outside it. AND,
be advised that it could be other components besides the chip, like
R-14, R-15 (both 47r, 1/4 watt) or C-103, 47uf/25v Bi-polar.
best,
Ike
Brian Simmons wrote:
Hi !
Thanks alot for your quick reply !
It seems to be the same for all the channels.
-Brian
--- On Tue, 1/6/09, Ike Zimbel <[email protected]> wrote:
From: Ike Zimbel <[email protected]>
Subject: Re: NEOTEK: problem with my Neotek Elan II
To: [email protected]
Date: Tuesday, January 6, 2009, 2:33 PM
Hi Brian,
Is this on a per channel basis, or right across the
board? If it is
individual channels, it is probably a bad solder joint on
the pan pot.
This is really common on the Elite and may also happen on
the Elan.
best,
Ike
Brian Simmons wrote:
I bought a Neotek Elan II about 3 years ago and have
run into a problem with my Aux A/B section. When I pan the
individual channel Aux A/B to the right I get a full sinal
out of "B" but if I pan to the left , I get a very
low level signal that sounds a bit distorted out of
"A". When I solo the master send for "A"
its the same low level distorted signal.
I have very little experience in electronics so any
help would be greatly appreciated.
thanks
-Brian
------
You can unsubscribe at anytime by sending an email to
mailto:[email protected] with "unsubscribe
neotek" in the message body. If you have any
difficulties, or questions --please send an email to
[email protected].
The Neotek list is lovingly hosted by Catapult Web
Development. Remember that any message or reply sent to the
list will be automatically forwarded to all subscribers.
Vive Le Neotek !
Thanks.
--
Ike Zimbel
Zimbel Audio Productions Ltd.
Toronto
416-720-0887
"Studio House Calls" - Repairs and upgrades to
analog audio equipment including: Amek, Allen & Heath,
Neve, Neotek, MCI, Soundcraft and more.
------
You can unsubscribe at anytime by sending an email to
mailto:[email protected] with "unsubscribe
neotek" in the message body. If you have any
difficulties, or questions --please send an email to
[email protected].
The Neotek list is lovingly hosted by Catapult Web
Development. Remember that any message or reply sent to the
list will be automatically forwarded to all subscribers.
Vive Le Neotek !
Thanks.
------
You can unsubscribe at anytime by sending an email to mailto:[email protected] with
"unsubscribe neotek" in the message body. If you have any difficulties, or
questions --please send an email to [email protected].
The Neotek list is lovingly hosted by Catapult Web Development. Remember that
any message or reply sent to the list will be automatically forwarded to all
subscribers.
Vive Le Neotek !
Thanks.
--
Ike Zimbel
Zimbel Audio Productions Ltd.
Toronto
416-720-0887
"Studio House Calls" - Repairs and upgrades to analog audio equipment including:
Amek, Allen & Heath, Neve, Neotek, MCI, Soundcraft and more.
------
You can unsubscribe at anytime by sending an email to mailto:[email protected] with
"unsubscribe neotek" in the message body. If you have any difficulties, or
questions --please send an email to [email protected].
The Neotek list is lovingly hosted by Catapult Web Development. Remember that
any message or reply sent to the list will be automatically forwarded to all
subscribers.
Vive Le Neotek !
Thanks.
