hey , Ive been searching the net to buy some NE-5532 dual opamps. Can someone give me a link to the correct ones to buy ? I want to make sure I get the right ones. thanks -Brian
--- On Tue, 1/6/09, Brian Simmons <[email protected]> wrote: > From: Brian Simmons <[email protected]> > Subject: Re: NEOTEK: problem with my Neotek Elan II > To: [email protected] > Date: Tuesday, January 6, 2009, 3:43 PM > Ok Ike , thanks alot for your help , Ill try replacing the > op-amp first and go from there. > > -Brian > > > --- On Tue, 1/6/09, Ike Zimbel > <[email protected]> wrote: > > > From: Ike Zimbel <[email protected]> > > Subject: Re: NEOTEK: problem with my Neotek Elan II > > To: [email protected] > > Date: Tuesday, January 6, 2009, 3:34 PM > > Ok, that could potentially be IC # U-4 on the master > module. > > It's an NE-5532 dual op-amp, 8 pin DIP package. > It's > > socketed so you should be able to pry it out with a > little > > screw driver and put the new one in. MAKE SURE you put > it in > > the right way up (the dot or notch on the end should > face > > the top of the module) That would be the master > module, BTW, > > the chip should be right under the "Aux A" > master > > pot. If you are not sure what you are doing, get help. > Also, > > make sure that all eight pins of the IC go into the > socket > > and don't bend under it or outside it. AND, be > advised > > that it could be other components besides the chip, > like > > R-14, R-15 (both 47r, 1/4 watt) or C-103, 47uf/25v > Bi-polar. > > best, > > Ike > > > > Brian Simmons wrote: > > > Hi ! > > > Thanks alot for your quick reply ! > > > > > > It seems to be the same for all the channels. > > > > > > -Brian > > > > > > > > > --- On Tue, 1/6/09, Ike Zimbel > > <[email protected]> wrote: > > > > > > > > >> From: Ike Zimbel > <[email protected]> > > >> Subject: Re: NEOTEK: problem with my Neotek > Elan > > II > > >> To: [email protected] > > >> Date: Tuesday, January 6, 2009, 2:33 PM > > >> Hi Brian, > > >> Is this on a per channel basis, or right > > across the > > >> board? If it is individual channels, it is > > probably a bad solder joint on > > >> the pan pot. This is really common on the > Elite > > and may also happen on > > >> the Elan. > > >> best, > > >> Ike > > >> > > >> Brian Simmons wrote: > > >> > > >>> I bought a Neotek Elan II about 3 years > ago > > and have > > >>> > > >> run into a problem with my Aux A/B section. > When I > > pan the > > >> individual channel Aux A/B to the right I get > a > > full sinal > > >> out of "B" but if I pan to the left > , I > > get a very > > >> low level signal that sounds a bit distorted > out > > of > > >> "A". When I solo the master send > for > > "A" > > >> its the same low level distorted signal. > > >> > > >>> I have very little experience in > electronics > > so any > > >>> > > >> help would be greatly appreciated. > > >> > > >>> thanks > > >>> -Brian > > >>> > > >>> > > >>> > > >>> > > >>> > > >>> ------ > > >>> > > >>> You can unsubscribe at anytime by sending > an > > email to > > >>> > > >> mailto:[email protected] with > > "unsubscribe > > >> neotek" in the message body. If you have > any > > >> difficulties, or questions --please send an > email > > to > > >> [email protected]. > > >> > > >>> The Neotek list is lovingly hosted by > > Catapult Web > > >>> > > >> Development. Remember that any message or > reply > > sent to the > > >> list will be automatically forwarded to all > > subscribers. > > >> > > >>> Vive Le Neotek ! > > >>> > > >>> Thanks. > > >>> > > >>> > > >> -- Ike Zimbel > > >> Zimbel Audio Productions Ltd. > > >> Toronto > > >> 416-720-0887 > > >> "Studio House Calls" - Repairs and > > upgrades to > > >> analog audio equipment including: Amek, Allen > > & Heath, > > >> Neve, Neotek, MCI, Soundcraft and more. > > >> > > >> > > >> ------ > > >> > > >> You can unsubscribe at anytime by sending an > email > > to > > >> mailto:[email protected] with > > "unsubscribe > > >> neotek" in the message body. If you have > any > > >> difficulties, or questions --please send an > email > > to > > >> [email protected]. > > >> > > >> The Neotek list is lovingly hosted by > Catapult > > Web > > >> Development. Remember that any message or > reply > > sent to the > > >> list will be automatically forwarded to all > > subscribers. > > >> Vive Le Neotek ! > > >> > > >> Thanks. > > >> > > > > > > > > > ------ > > > > > > You can unsubscribe at anytime by sending an > email to > > mailto:[email protected] with "unsubscribe > > neotek" in the message body. If you have any > > difficulties, or questions --please send an email to > > [email protected]. > > > > > > The Neotek list is lovingly hosted by Catapult > Web > > Development. Remember that any message or reply sent > to the > > list will be automatically forwarded to all > subscribers. > > > Vive Le Neotek ! > > > > > > Thanks. > > > > > > > > > > -- Ike Zimbel > > Zimbel Audio Productions Ltd. > > Toronto > > 416-720-0887 > > "Studio House Calls" - Repairs and upgrades > to > > analog audio equipment including: Amek, Allen & > Heath, > > Neve, Neotek, MCI, Soundcraft and more. > > > > > > ------ > > > > You can unsubscribe at anytime by sending an email to > > mailto:[email protected] with "unsubscribe > > neotek" in the message body. If you have any > > difficulties, or questions --please send an email to > > [email protected]. > > > > The Neotek list is lovingly hosted by Catapult Web > > Development. Remember that any message or reply sent > to the > > list will be automatically forwarded to all > subscribers. > > Vive Le Neotek ! > > > > Thanks. > > > > ------ > > You can unsubscribe at anytime by sending an email to > mailto:[email protected] with "unsubscribe > neotek" in the message body. If you have any > difficulties, or questions --please send an email to > [email protected]. > > The Neotek list is lovingly hosted by Catapult Web > Development. Remember that any message or reply sent to the > list will be automatically forwarded to all subscribers. > Vive Le Neotek ! > > Thanks. ------ You can unsubscribe at anytime by sending an email to mailto:[email protected] with "unsubscribe neotek" in the message body. If you have any difficulties, or questions --please send an email to [email protected]. The Neotek list is lovingly hosted by Catapult Web Development. Remember that any message or reply sent to the list will be automatically forwarded to all subscribers. Vive Le Neotek ! Thanks.
