I have a Kodak USB Picture Card Reader for CompactFlash cards.When I was running Windows, I needed a driver from Kodak as far as I remember.
Heres a link to the Windows driver so you know the product: http://wwwdk.kodak.com/global/en/service/downloads/dln_ekn.jhtml?ekn=EKN020812 The thing is that if I plug in the card reader to my USB port, Mandrake wont even boot. Theres no messages, it just stops during boot. If the card reader is not plugged in, I can see my USB port during boot: usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb-uhci.c: $Revision: 1.275 $ time 11:59:06 Sep 18 2003 usb-uhci.c: High bandwidth mode enabled PCI: Enabling device 00:09.0 (0014 -> 0015) PCI: Found IRQ 9 for device 00:09.0 PCI: Sharing IRQ 9 with 00:10.0 usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 9 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected PCI: Enabling device 00:09.1 (0014 -> 0015) PCI: Found IRQ 11 for device 00:09.1 PCI: Sharing IRQ 11 with 01:00.0 usb-uhci.c: USB UHCI at I/O 0xd000, IRQ 11 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 2 ports detected PCI: Found IRQ 3 for device 00:11.2 IRQ routing conflict for 00:11.2, have irq 9, want irq 3 IRQ routing conflict for 00:11.3, have irq 9, want irq 3 usb-uhci.c: USB UHCI at I/O 0xa400, IRQ 9 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 3 hub.c: USB hub found hub.c: 2 ports detected PCI: Found IRQ 3 for device 00:11.3 IRQ routing conflict for 00:11.2, have irq 9, want irq 3 IRQ routing conflict for 00:11.3, have irq 9, want irq 3 usb-uhci.c: USB UHCI at I/O 0xa000, IRQ 9 usb-uhci.c: Detected 2 ports usb.c: new USB bus registered, assigned bus number 4 hub.c: USB hub found hub.c: 2 ports detected usb-uhci.c: v1.275:USB Universal Host Controller Interface driver PCI: Enabling device 00:09.2 (0014 -> 0016) PCI: Assigned IRQ 5 for device 00:09.2 PCI: Sharing IRQ 5 with 00:05.0 PCI: Sharing IRQ 5 with 00:0e.0 ehci_hcd 00:09.2: VIA Technologies, Inc. USB 2.0 ehci_hcd 00:09.2: irq 5, pci mem f8900000 usb.c: new USB bus registered, assigned bus number 5 ehci_hcd 00:09.2: USB 2.0 enabled, EHCI 0.95, driver 2003-Jun-19/2.4 hub.c: USB hub found hub.c: 4 ports detected usbdevfs: remount parameter error Can I get this card reader to work somehow? Best regards SÃren
Want to buy your Pack or Services from MandrakeSoft? Go to http://www.mandrakestore.com