But pie ok
On Wed, Mar 11, 2009 at 10:44 AM, Josh Bowlin <schwah...@gmail.com> wrote: > NO SOUP FOR YOU! > > > On Wed, Mar 11, 2009 at 10:43 AM, Graham Rogers <graha...@ptd.net> wrote: > >> Can I have a number? >> >> On Mar 11, 2009, at 10:40 AM, Kyle Munz wrote: >> >> Then I want to change my number too... >> >> -Kyle #138 >> >> On Wed, Mar 11, 2009 at 10:30 AM, Kyle K.K. <not.chr...@gmail.com> wrote: >> >>> >>> Well, maybe I can con a friend of mine into fabbing up some stainless >>> panels.... >>> >>> Because I don't like being Kyle #2 >>> -Kyle #13 >>> >>> On Wed, Mar 11, 2009 at 9:23 AM, Kyle Munz <kyle...@gmail.com> wrote: >>> > I just noticed that this conversation now has two Kyles and Two >>> Grahams, now >>> > all we need is one more hotrodmamma >>> > >>> > -Kyle #1 >>> > >>> > On Wed, Mar 11, 2009 at 10:16 AM, Graham Rogers <graha...@ptd.net> >>> wrote: >>> >> >>> >> Why don't you try air side panels Kyle - they never need cleaning, >>> it's >>> >> easy to see what's behind them and they don't need attaching, Graham >>> >> On Mar 11, 2009, at 9:27 AM, Kyle Munz wrote: >>> >> >>> >> I'm going to make new side panels out of paper mache, I'll let you >>> know >>> >> how that goes... >>> >> >>> >> -Kyle >>> >> >>> >> >>> >> On Wed, Mar 11, 2009 at 9:24 AM, Creative Residential Designs >>> >> <finderskeep...@qwest.net> wrote: >>> >>> >>> >>> Yes, but in this case the 550 panel is substantially smaller that a >>> 650 >>> >>> panel. I envision hacking the thing in two both directions and then >>> >>> re-studding it too....hmm. An experiment that I will wait for the >>> results >>> >>> on. >>> >>> (P.S...I have both a 550 and a 650 in my shop. I would be willing to >>> >>> measure >>> >>> the 550 panel for our friend here and maybe he can manufacture one.) >>> >>> Hotrod. >>> >>> >>> >>> ----- Original Message ----- >>> >>> From: <cakra...@gmail.com> >>> >>> To: "Nighthawk Motorcycle Lovers!" < >>> nighthawk_lovers@googlegroups.com> >>> >>> Sent: Wednesday, March 11, 2009 3:36 AM >>> >>> Subject: [Nighthawk Lovers] Re: Body panel question >>> >>> >>> >>> >>> >>> >>> >>> I would like to add to this that I had some success repairing one of >>> >>> the plastic mounting studs on the inside of my '86 CB700SC. The >>> >>> rearward stud on the left side busted from... stuff, and i lost the >>> >>> piece too. I waited it out for the OE rubber grommet piece to come >>> in >>> >>> the mail. I went to Motorcycles Unlimited, in Stanton, CA and found a >>> >>> similar, but longer stud off an old Yamaha I think. I stuck the >>> hack- >>> >>> job together using some bent welding rod for support, and Permatex 2- >>> >>> part plastic weld epoxy and my Dremmel for a custom fit. The grommet >>> >>> was like two or three dollars and I had the other stuff so this >>> >>> repair, although time consuming, is super low cost. For alteration >>> of >>> >>> body panels... good luck hotrod.. >>> >>> >>> >>> On Mar 10, 10:10 pm, "Creative Residential Designs" >>> >>> <finderskeep...@qwest.net> wrote: >>> >>> > No can do partner. It's PLASTIC. You can go pound one out of sheet >>> >>> > metal >>> >>> > and >>> >>> > weld some tabs on. Get out your calculator and ruler..Hotrod. >>> >>> > >>> >>> > ----- Original Message ----- >>> >>> > From: "Kyle K.K." <not.chr...@gmail.com> >>> >>> > To: <nighthawk_lovers@googlegroups.com> >>> >>> > Sent: Tuesday, March 10, 2009 10:54 PM >>> >>> > Subject: [Nighthawk Lovers] Re: Body panel question >>> >>> > >>> >>> > > I'd be willing to modify the body panel. I'm just tired of my >>> right >>> >>> > > side panel almost falling off. >>> >>> > >>> >>> > > On Tue, Mar 10, 2009 at 10:25 PM, Dennis Hammerl < >>> blues...@yahoo.com> >>> >>> > > wrote: >>> >>> > >> Why don't you check an on-line Honda parts look-up and see if >>> both >>> >>> > >> parts >>> >>> > >> have the same number ? (hint... they don't) >>> >>> > >>> >>> > >> --- On Tue, 3/10/09, Kyle K.K. <not.chr...@gmail.com> wrote: >>> >>> > >>> >>> > >> From: Kyle K.K. <not.chr...@gmail.com> >>> >>> > >> Subject: [Nighthawk Lovers] Body panel question >>> >>> > >> To: nighthawk_lovers@googlegroups.com >>> >>> > >> Date: Tuesday, March 10, 2009, 9:28 AM >>> >>> > >>> >>> > >> Anyone know if a right hand side 650 side panel will work (with >>> >>> > >> modification if need be) on an '83 550? >>> >>> > >>> >>> > >> -Kyle >>> >>> >>> >>> >>> >>> >>> >>> >>> >>> >>> >> >>> >> >>> >> >>> >> >>> >> >>> >> >>> >> >>> > >>> > >>> > > >>> > >>> >>> >>> >> >> >> >> >> >> >> >> > --~--~---------~--~----~------------~-------~--~----~ You received this message because you are subscribed to the Google Groups "Nighthawk Motorcycle Lovers!" group. To post to this group, send email to nighthawk_lovers@googlegroups.com To unsubscribe from this group, send email to nighthawk_lovers+unsubscr...@googlegroups.com For more options, visit this group at http://groups.google.com/group/nighthawk_lovers?hl=en -~----------~----~----~----~------~----~------~--~---
