So I'm finally getting around to taking off the clutch fluid cap and the screws just melt ... 30 year old bike with a gorilla putting them on ... pretty stripped. Anybody else have to work with these small stripped screws before?
Drill through them and try to find replacements and/or seal with duct tape?? On Sunday, September 27, 2015 at 6:23:21 PM UTC-5, Mike21222 wrote: > > Very good tips. > Let me add 2 more. > > 1) Don't get any of that brake fluid on anything you don't want to > repaint. It will strip the paint right off of your tank, fenders and much, > much more.. > > 2) In case a partial or full rebuild is needed, I completely rebuilt my > clutch master and slave cylinders in just a few hours with under $100 in > parts using tips from folks in this forum and the clymer repair manual. > > > > -----Original Message----- > From: pa_sk8r <pa_...@verizon.net <javascript:>> > To: nighthawk_lovers <nighthaw...@googlegroups.com <javascript:>> > Sent: Sun, Sep 27, 2015 10:55 am > Subject: [Nighthawk Lovers] 85 nh650 ... clutch??? > > Welcome to the Group! > > If you don't have a repair manual, it's highly > recommended > Occasionally you can find tutorials on youtube that are helpful > > > Sometimes the small seals in the piston of the master cylinder go bad. > > The > problem I found with my 550 & 650 were the seals in the slave cylinder were > shot. > When I removed the 3 bolts on the side of the case near the shifter, it > looked like cottage cheese inside & nothing like fluid! > > You'll need seals #9 > & 15 in this > diagram- > http://www.bikebandit.com/oem-parts/1983-honda-night-hawk-650-cb650sc/o/m151745#sch558418 > > There's > also a kit available from E-bay with the seals $15.50 & free shipping- > > http://www.ebay.com/itm/Honda-CB-550-650-700-SC-1983-1986-Nighthawk-Clutch-Slave-Cylinder-Repair-Kit-NEW-/311447662191?fits=Make%3AHonda&hash=item4883ba2e6f&vxp=mtr > > -Bernie > > On > 09/27/15, ADAMinIowa wrote: > > Following symptoms after starting fine in > neutral: > - clunks out / jerks forward when put into 1st (even with clutch > handle engaged) > - I can get it going by giving itgas when putting in gear > (jerky/rough) > - Clunks out coming up to stop > - clutch handle has almost no > tension > - still feel the rpms change when shifting even with clutch handle > fully engaged > - really hard shifting between gears with pedal > > Basically > feels like the clutch is always let out. > > Flush fluid? Anything > else? > > First timer w this stuff, thanks!!!! > > -- > You received this message > because you are subscribed to the Google Groups "Nighthawk Motorcycle Lovers!" > group. > To unsubscribe from this group and stop receiving emails from it, send > an email to nighthawk_love...@googlegroups.com <javascript:>. > To post to this > group, send email to nighthaw...@googlegroups.com <javascript:>. > Visit this group athttp://groups.google.com/group/nighthawk_lovers. > For more options, visithttps://groups.google.com/d/optout. > > -- > You received this message because > you are subscribed to the Google Groups "Nighthawk Motorcycle Lovers!" > group. > To unsubscribe from this group and stop receiving emails from it, send > an email to nighthawk_love...@googlegroups.com <javascript:>. > To post to this > group, send email to nighthaw...@googlegroups.com <javascript:>. > Visit this group athttp://groups.google.com/group/nighthawk_lovers. > For more options, visithttps://groups.google.com/d/optout. > > -- You received this message because you are subscribed to the Google Groups "Nighthawk Motorcycle Lovers!" group. To unsubscribe from this group and stop receiving emails from it, send an email to nighthawk_lovers+unsubscr...@googlegroups.com. To post to this group, send email to nighthawk_lovers@googlegroups.com. Visit this group at http://groups.google.com/group/nighthawk_lovers. For more options, visit https://groups.google.com/d/optout.
