Forgot to mention, but the previous error occured with 0.7.0. This is what
I am getting with 0.6.1 and 0.5.0 while having the same set up and
configuring with --enable-ft2232_libftdi:
>>>>>>
Info : 281 63 core.c:951 jtag_examine_chain_display(): JTAG tap:
omapl138.jrc tap/device found: 0x1b7d102f (mfg: 0x017, part: 0xb7d1, ver:
0x1)
Warn : 282 63 core.c:951 jtag_examine_chain_display(): JTAG tap:
omapl138.jrc UNEXPECTED: 0x1b7d102f (mfg: 0x017, part: 0xb7d1, ver:
0x1)
Error: 283 63 core.c:951 jtag_examine_chain_display(): JTAG tap:
omapl138.jrc expected 1 of 1: 0x0b7d102f (mfg: 0x017, part: 0xb7d1, ver:
0x0)
Error: 284 63 core.c:1457 jtag_init_inner(): Trying to use configured scan
chain anyway...
Debug: 285 63 core.c:1208 jtag_validate_ircapture(): IR capture validation
scan
Debug: 286 65 core.c:1267 jtag_validate_ircapture(): omapl138.jrc: IR
capture 0x01
Warn : 287 65 core.c:1480 jtag_init_inner(): Bypassing JTAG setup events
due to errors
<<<<<<
Got a clue how to proceed?
On Mon, Jul 8, 2013 at 6:40 PM, Laszlo Papp <[email protected]> wrote:
> Hi,
>
> based on my previous email thread [1], I switched to the jtag in the
> subject. I was wondering if anyone had a clue about this failure before I
> start digging into the details, and perhaps even into the openocd code:
>
> >>>>>>
>
> User : 444 213 arm926ejs.c:534 arm926ejs_arch_state(): MMU: enabled, D-Cache:
> enabled, I-Cache: disabled
> Debug: 445 213 command.c:145 script_debug(): command - ocd_command
> ocd_command type ocd_mww 0x68000010 0x00a00505
> Debug: 446 213 command.c:145 script_debug(): command - mww ocd_mww 0x68000010
> 0x00a00505
> Debug: 448 215 target.c:1683 target_write_buffer(): writing buffer of 4 byte
> at 0x68000010
> Debug: 449 233 arm7_9_common.c:2107 arm7_9_read_memory(): address:
> 0xc70f9a00, size: 0x00000004, count: 0x00000001
> Debug: 450 239 armv4_5_mmu.c:47 armv4_5_mmu_translate_va(): 1st lvl desc:
> 00000000
> Error: 451 239 armv4_5_mmu.c:50 armv4_5_mmu_translate_va(): Address
> translation failure
> Debug: 452 239 command.c:631 run_command(): Command failed with error code
> -309
>
> <<<<<<
>
> Many thanks,
> Laszlo
>
> [1] http://comments.gmane.org/gmane.comp.debugging.openocd.devel/23429
>
------------------------------------------------------------------------------
This SF.net email is sponsored by Windows:
Build for Windows Store.
http://p.sf.net/sfu/windows-dev2dev
_______________________________________________
OpenOCD-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/openocd-devel
