Daveed, Yes, you position your highlight on the start phrase and then specify the end phrase to be deleted and your new audio should then delete the selected phrases and replace them with the newly recorded material.
Jamie -----Original Message----- From: Daveed Mandell [mailto:[EMAIL PROTECTED] Sent: 02 June 2004 05:54 To: [EMAIL PROTECTED] Subject: RE: Overwrite Mode In punch-in mode, do you have to specify an ending phrase or any endpoint? Anyway, the facilities are excellent, just confusing! h--Daveed-- On Wed, 2 Jun 2004 [EMAIL PROTECTED] wrote: > Daveed, > > Are you talking about the PTR1 or the PRS software? > > A quick explanation: > > PTR1: > On the PTR1 the terms used are "Insert" and "Punch-In". Insert means what > it sounds like i.e. when you select a position in your audio and start > recording, the new audio will be inserted into the existing audio at the > location specified. No deletion will occur. > The "Punch in" mode allows you to specify a group of phrases that will be > replaced with the new audio. This can be as little as a single phrase up to > the whole of the original recording. > > PRS: > There has been some confusion over the fact that different terminology is > used in the PTR1 and the PRS. On the PRS the two phrases used are > "Overwrite" and "Punch in". This can be quite confusing, however, I'll try > to clarify things. Overwrite means that the new recording will completely > overwrite the section you are focussed on from the highlighted phrase to the > end of that section. You do not need to specify particular phrases apart > from the starting point, it will assume that everything else in the section > is to be deleted and replaced with the new audio. The confusion is the use > of the "Punch in" option. This can be used to either insert audio (as in > the PTR1 or can be used to behave like the punch in facility on the PTR1. > The thing that decides which way you want to use this facility is in the > dialogue box that appears when you go into recording pause mode. In the > list of phrases displayed, the top item is "Nothing". If you leave this > selected, "Punch in" will act like the insert mode. If you specify any or > all of the phrases in the list, "Punch in" will behave like the punch in > facility on the PTR1. > > I know that is a bit confusing but I assure you that this all works. > > Hope this helps. > > Jamie > > > > -----Original Message----- > From: Daveed Mandell [mailto:[EMAIL PROTECTED] > Sent: 02 June 2004 05:14 > To: [EMAIL PROTECTED] > Subject: Overwrite Mode > > > While making rec ordings of voice tracks and other narrative material, I > and my readers have been grappling with Insert, Punch-in and Overwrite > modes. > When using Overwrite, and one wants to go back and record over a mistake, > can one simply continue recording from that passage? > I like the fact that you can pause the recording and simply rewind a few > phrases and quickly cut in and record over the mistake. > > My readers are still confused about Punch-in versus Insert modes. > > In a studio setting, we have been able to produce very professional > recordings with no discernible clicks when correcting errors or adding to > recordings. > Of course, using broadcast-quality microphones helps, too. > > My only big cvomplaints about the Plextalk is its inability to allow for > knowing and > determining time increments in a specific passage, rather than a complete > title--and its > rather short battery life--a problem for a broadcast journalist in the > field without the possibility of > plugging the unit into a power outlet. Other than those concerns, it's a > great unit, and my > sighted colleagues appear to admire it. > g--Daveed- > > > --------------------------------------------------------------------- > To unsubscribe, e-mail: [EMAIL PROTECTED] > For additional commands, e-mail: [EMAIL PROTECTED] > > -- > DISCLAIMER: > > NOTICE: The information contained in this email and any attachments is > confidential and may be privileged. If you are not the intended > recipient you should not use, disclose, distribute or copy any of the > content of it or of any attachment; you are requested to notify the > sender immediately of your receipt of the email and then to delete it > and any attachments from your system. > > RNIB endeavours to ensure that emails and any attachments generated by > its staff are free from viruses or other contaminants. However, it > cannot accept any responsibility for any such which are transmitted. > We therefore recommend you scan all attachments. > > Please note that the statements and views expressed in this email and > any attachments are those of the author and do not necessarily represent > those of RNIB. > > RNIB Registered Charity Number: 226227 > > Website: http://www.rnib.org.uk > > --------------------------------------------------------------------- > To unsubscribe, e-mail: [EMAIL PROTECTED] > For additional commands, e-mail: [EMAIL PROTECTED] > --------------------------------------------------------------------- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED] -- DISCLAIMER: NOTICE: The information contained in this email and any attachments is confidential and may be privileged. If you are not the intended recipient you should not use, disclose, distribute or copy any of the content of it or of any attachment; you are requested to notify the sender immediately of your receipt of the email and then to delete it and any attachments from your system. RNIB endeavours to ensure that emails and any attachments generated by its staff are free from viruses or other contaminants. However, it cannot accept any responsibility for any such which are transmitted. We therefore recommend you scan all attachments. Please note that the statements and views expressed in this email and any attachments are those of the author and do not necessarily represent those of RNIB. RNIB Registered Charity Number: 226227 Website: http://www.rnib.org.uk --------------------------------------------------------------------- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED]
