Yea, i suspected that. Me bad. been a while for sure.
On 6/25/2020 6:31:24 PM, William Miller <will...@millersolar.com> wrote:
Kirk:
If my memory is correct: What you describe below are port assignments if one is
stacking FXR inverters for 120/240 with a Hub 10.3. It also requires changing
DIP jumpers from factory defaults. This is not accurate for stacking Radians.
With Radians I think secondary inverters can use any port but I have always
used 2 through X for secondaries.
William
From: RE-wrenches [mailto:re-wrenches-boun...@lists.re-wrenches.org
[mailto:re-wrenches-boun...@lists.re-wrenches.org]] On Behalf Of Kirk Herander
Sent: Thursday, June 25, 2020 2:07 PM
To: re-wrenches@lists.re-wrenches.org [mailto:re-wrenches@lists.re-wrenches.org]
Subject: Re: [RE-wrenches] Slave Radian not showing up on Hub10 or @ Mate3s
The master-slave config types and port assignments have always been confusing.
The quick start guide lists a config where the master is port 1 and the slave
is port 7. I believe port 7 is called the sub-master in this config. With only
2 inverters it functions as the slave to the master in port 1. This config has
always worked for me.
Hope this is accurate info.
On 6/25/2020 1:35:55 PM, Chris Schaefer <ch...@solarandwindfx.com
[mailto:ch...@solarandwindfx.com]> wrote:
G'Day All,
So I started up a system recently with two Radian 8048A's. The master is
connected to port 1 and the slave connected to port 2 with the FlexNet at port
3. There are no OB charge controllers in the system. When the hub is polling
(led's scrolling) nothing shows up for the slave at port 2. It's like the slave
inverter doesn't exist. So I moved the slave and flexnet down to port 3 and 4.
No change in the polling. I swapped out comm (factory green) cables. Again no
change. Looking at the control board of the slave there is only one green led
on which is located at the upper right-hand side. Otherwise no led's are on. I
have 57v at the buss bar terminals of the inverter. Of course since there is no
polling at the hub there is no way to view port 2 to view the slave at the Mate.
Now the only thing that I didn't do was to try and use the manual on/off
switch-jumper to start the slave. But in the past regardless of the inverter
being on or off it would still show up on the hub. This is a new one and I'm
looking for some direction here.
Thanks,
Christopher-
Chris Schaefer’s
Error! Filename not specified. [http://www.solarandwindfx.com]
Tel/Fax 585-229-2083 or Cell 585-748-1870
5115 South Hill Road ~ Canandaigua New York 14424
www.solarandwindfx.com [http://www.solarandwindfx.com] ~ E-mail:
ch...@solarandwindfx.com [mailto:ch...@solarandwindfx.com]
Error! Filename not specified.
Thomas Jefferson, the author of our great Constitution, once said, "democracy"
will cease to exist when you take away from those who are willing to work and
give to those who would not."
_______________________________________________ List sponsored by Redwood
Alliance List Address: RE-wrenches@lists.re-wrenches.org
[mailto:RE-wrenches@lists.re-wrenches.org] Change listserver email address &
settings: http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
[http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org]
List-Archive:
http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html
[http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html]
List rules & etiquette: www.re-wrenches.org/etiquette.htm
[http://www.re-wrenches.org/etiquette.htm] Check out or update participant
bios: www.members.re-wrenches.org [http://www.members.re-wrenches.org]
_______________________________________________
List sponsored by Redwood Alliance
List Address: RE-wrenches@lists.re-wrenches.org
Change listserver email address & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
List-Archive:
http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html
List rules & etiquette:
www.re-wrenches.org/etiquette.htm
Check out or update participant bios:
www.members.re-wrenches.org
